Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
754652 Capacity (mild steel)............. Shearing Length Capacity..... Back Gauge Capacity........... Front Gauge Capacity........... Overall Dimensions (LxWxH) Net Weight (lbs.)................... 16 gauge....................... ....................... 16 gauge 36”................................ .................................52” 25.5”............................. ..............................25.5” 28”................................ .................................28” 46 7” x 21 %” x 41 7”... ...62 7” x 21 %” x 41 7” 824 .............................. ..............................1014 Uncrating and Clean-Up 1. Remove the crate from around the machine. 2. Carefully clean all rust protected surfaces with a mild solvent or kerosene and a soft rag. Do not use lacquer thinner, paint thinner, or gasoline. These will damage painted surfaces. 3. Coat all machined surfaces with a light coat of oil to inhibit rust. 4. Remove the bolts holding the machine to the skid. 5. Carefully move the machine to a level foundation. Machine location must allow access to all sides. Assembly Note: Prior to shipment the foot shear is adjusted at the factory for proper operation. If the machine does not operate properly or the stand does not sit squarely on the floor, proceed to setup. Stop Assembly The (#) in the text refers to the breakdown. 1. Attach the two front arm extensions #6 to the bed with four hex cap screws and washers. 2. Attach the stop #71 to the front extension arms with T-nuts #72. 3. Attach the rear stop #59 to the adjusting block assembly #61. 4. Insert the rod #58 through the adjusting block assembly and into the cutter bar. Tighten in place with knobs #65. Setup 1. Loosen four bolts #21. Loosen adjusting screws #18 & 19. The bed must rest squarely on the right and left hand side panels at all four corners while screws are loose. Shim legs at floor if necessary. Tighten hardware. 2. Use set screw #18 and hex cap screw #19, to adjust the lower blade towards or away from the upper blade. The distance between the upper and lower blades should be 0.0020.005”. Do not let the blades overlap. 3. Place a heavy sheet of paper (~0.005”) in the cutting position, along the entire length of the bed, and slowly press the foot lever. 4. If the shear does not cut the paper move the lower blade towards the upper blade. 5. If the shear cuts the paper on the ends, but not the center, turn the tie-rod adjusting screw #37, clockwise until the paper is cut the entire length. 6. If the shear cuts the paper in the center, but not the ends, turn the tie-rod adjusting screw #37, counter-clockwise until the paper is cut the entire length. 7. Make sure the scales #15 and #16 on top of the bed are square to the blade, and also show the correct distance from the blade. 8. Make test cuts to verify the scales are correct. Blade Care The 2-way upper blade can be removed and flipped 180°, for a sharp edge before having to sharpen the blade. Wipe the blade lightly with oil. Lubricate all pivot points on the machine daily. Spring Tension The spring return can be adjusted on the foot lever by tightening #46 hex nuts. The spring return can be adjusted on the hold down #3 by tightening #10 hex nuts. Gib Adjustment There are three hex cap screws #32 that can be adjusted for play in the shim #31. Adjust for smooth travel. 4 Breakdown for FS-1636N & FS-1652N Foot Shear 5 Parts List for the FS-1636N & FS-1652N Foot Shear Index Part No. No. Description Size Quantity 1..........FS1636N-1...................Table.................................................................................................. ............FS1652N-1...................Table.................................................................................................. 2..........FS1636N-2...................Cutter Bar........................................................................................... ............FS1652N-2...................Cutter Bar........................................................................................... 3..........FS1636N-3...................Hold Down.......................................................................................... ............FS1652N-3...................Hold Down.......................................................................................... 4..........FS1636N-4...................R.H. Side Panel.................................................................................. 5..........FS1636N-5...................L.H. Side Panel................................................................................... 6..........FS1636N-6...................Front Arm Extension.............................................................................2 7..........FS1636N-7...................Screw....................................................M12x45...................................4 8..........FS1636N-8...................Spring...
Este manual também é adequado para os modelos :Clippers - FS-1636N (144.51 kb)