Assessments - 5, GPA: 3.6
(
)
)
|
Facilidade de uso
• Align the hole in the throttle handle for the fixing screw with the hole on the handlebars. • Refit the screw in the rear of the throttle handle. • Fit the screw through the throttle handle and the handlebars and tighten. • Unscrew the handle from the handlebar bracket. • Position the handlebars as shown. Fit the bracket components and tighten the handle lightly. • Put on the harness and hang the machine in the suspension hook. Now finely adjust so that the machine gives a comfortable working position when it‘s attached to the harness. Tighten the handle. Assembling the handlebars (245RX, 252RX) • Unscrew the handle from the handlebar bracket. • Position the handlebars as shown. Fit the bracket components and tighten the handle lightly. • Fit the right hand grip to the handlebar using the bolt, washer, sleeve and nut as shown. Tighten the bolt. • Put on the harness and hang the machine in the suspension hook. Now finely adjust so that the machine gives a comfortable working position when it‘s attached to the harness. Tighten the handle. Transport position, handlebars (240R, 245R/RX, 250R, 252RX) • The handlebars can easily be turned to fit along the shaft for easy transportation and storage. • Loosen the knob. Turn the handles clockwise so that the throttle comes against the engine. • Thereafter fold the handlebars around the shaft. Tighten the handle. • Attach the transport guard. 22 – English ASSEMBLY Assembling the handlebars (265RX) • Fit the left handle in the handle support. • Fit the right handle. • Make a first adjustment and tighten the screws slightly. • Then make the final adjustment with the clearingsaw in the harness, to obtain the most suitable working position. Tighten the screws. • Make a final adjustment of the right handle and fix it in the most comfortable position. Adjusting the throttle control Adjust the throttle control for the most suitable working position. Use the socket head screws at the right handle. English – 23 ASSEMBLY Assembly of the blade and trimmer head It is extremely important that the disc drive’s/support flange’s guide engages correctly in the cutting equipment’s centre hole when assembling the cutting equipment. Cutting equipment assembled incorrectly can result in serious and/or fatal personal injury. ! ! WARNING! Do not attach any blade to the unit without proper installation of all required parts. Failure to use the proper parts can cause the blade to fly off and seriously injure the operator and/or bystanders. Under no circumstances may the cutting equipment be used without an approved guard fitted. See the chapter “Technical data”. If the wrong guard or a defective guard is fitted this can cause serious personal injury. IMPORTANT INFORMATION The machine must be equipped with the correct handlebars, blade guard and harness if either a clearing blade or grass blade are to be used. Assembling the blade guard and grass blade • The guard (A) is fitted using 4 screws (L) and the support plate (M) as set out in the diagram. NOTE! Use the recommended blade guard. • Fit the drive disc (B) on the output axle. • Turn the blade axle until one of the holes in the drive disc aligns with the hole in the gear housing. • Insert the locking pin (C) in the hole so that the axle is locked. • Place the blade (D), support cup (E) and support flange (F) on the output axle. • Fit the nut (G). The tightening torque of the nut is 35-50 Nm (3,5 - 5 kpm). Use the socket spanner in the tool kit. Hold the handle of the G F E D B C A L M spanner as close to the blade guard as possible. The nut is tightened when the spanner is turned against the direction of rotation (left-hand thread). Assembling the blade guard and clearing blade • The guard (A) is fitted using 4 screws (L) as set out in the diagram. NOTE! Use the recommended blade guard. • Fit the drive disc (B) on the output axle. • Turn the blade axle until one of the holes in the drive disc aligns with the hole in the gear housing. • Insert the locking pin (C) in the hole so that the axle is locked. • Place the blade (D) and support flange (F) on the output axle. • Fit the nut (G). The tightening torque of the nut is 35-50 Nm (3.5 - 5 kpm). Use the socket spanner in the tool kit. Hold the handle of the spanner as close to the blade guard as possible. The nut is tightened when the spanner is turned against the direction of rotation (left-hand thread). • When slacking off and tightening the saw blade nut, the hands may be injured by the blade teeth. Always hold your hand protected by the blade guard. This is facilitated by the use of a long box spanner. The illustration shows the area in which you should keep the box spanner. L A G F D B C 24 – English ASSEMBLY Assembling the spray guard and trimmer head Trimmy SII • Fit the correct guard (A) for working with a trimmer head. Secure using 4 bolts (L) and the support plate (M) as shown. • Fit the driver plate (B) on the drive shaft. • Rotate the drive shaft so that one of the holes in the ...
Este manual também é adequado para os modelos :Clippers - 245 RX (1.97 mb)