Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
preparing for use Charging Charge the appliance for at least 12 hours before you use it for the first time. A fully charged appliance has a cordless operating time of up to 35 minutes. Do not charge the appliance for more than 24 hours. 1 Make sure the appliance is switched off. English 2 3 Insert the appliance plug into the appliance. Put the adapter in the wall socket. The charging light goes on to indicate that the , appliance is charging. Note:The charging light does not change colour and does not go out when the appliance is fully charged. optimising the lifetime of the battery -Discharge the batter y completely twice a year by letting the motor run until it stops. -Remove the adapter from the wall socket when the batter y is fully charged. -If you have not used the appliance for a long time, recharge it for at least 12 hours. Corded clipping When the rechargeable batter y is empty, you can also run the appliance from the mains. Do not run the appliance from the mains when the battery is fully charged. To use the hair clipper connected to the mains: 1 2 Switch off the hair clipper and connect it to the mains. Wait a few seconds and then switch on the appliance. Using the appliance Clipping with comb attachment Note: Make sure your hair is clean and dry. Do not use the appliance on freshly washed hair. 1 Comb your hair with a styling comb in the hair growth direction. 2 Slide the comb attachment into the guiding grooves of the appliance (‘click’). 3 To set the comb attachment to the desired hair length setting, press the adjustment button (1) and slide the comb attachment upwards or downwards (2). Hair length settings With the comb attachment attached, the appliance has 7 different hair length settings: Hair length setting Resulting hair length 1 3mm 2 6mm 3 9mm 4 12mm 5 15mm 6 18mm 7 21mm 1 2 English 7 English 4 5 6 Put the adapter in the wall socket. Wait a few seconds and then slide the on/off switch to the ‘on’ position. Move the appliance through the hair slowly. -Star t clipping at the highest setting of the comb attachment and reduce the hair length setting gradually. -Write down the hair length settings you selected to create a cer tain hairstyle as a reminder for future clipping sessions. -To clip in most effectively, move the appliance against the hair growth direction. -Since all hair does not grow in the same direction, you need to move the appliance in different directions (upwards, downwards and across). -Make overlapping passes over the head to ensure that you cut all the hair that needs to be cut. -Make sure that the flat par t of the hair clipping comb attachment is fully in contact with the scalp to obtain an even cutting result. -To achieve a good result with curly, sparse or long hair, use a styling comb to guide the hair towards the appliance. 7 Regularly remove cut hair from the comb attachment. If a lot of hair has accumulated in the comb attachment, remove it from the appliance and blow and/or shake the hair out of it. English graduation The Philips hair clipper not only allows you to cut the hair evenly at the same length all over the head, it also enables you to achieve a smooth transition from longer hair on top of the head to shor ter hair on the back and sides of the head. 1 2 Start clipping at setting 7 for the maximum remaining hair length of 21mm. Then choose a lower setting for a shorter remaining hair length. Cut the hair on all parts of the head except the top, where you want the hair to be longer. 3 You can repeat this procedure until the hair on every part of the head has the desired length. precise contouring without comb attachment You can use the appliance without comb attachment to contour the neckline and the area around the ears. Note:When you use the appliance without comb attachment, it cuts the hair very close to the skin. 1 2 3 Pull the comb attachment off the appliance. Before you start to contour the hairline around the ears, comb the hair ends over the ears. Tilt the appliance in such a way that only one edge of the cutting element touches the hairends. 4 Only cut the hair ends. The hairline has to be close to the ear. 5 To contour the neckline and sideburns, turn the appliance and make downward strokes. 6 Move the appliance slowly and smoothly. Follow the natural hairline. Cutting over styling comb or fingers This technique can be used to obtain hair lengths over 21 mm. Bear in mind that this technique is difficult to master and should only be applied by experienced users. 1 Remove the comb attachment. 2 Comb a small section of hair upwards. Lift the hair with a styling comb or hold it between your fingers until only the length that needs to be cut sticks out. 10 English 3 Cut the hair protruding from the comb or fingers. 4 Continue this procedure and comb frequently to remove cut hair and to check for unevenly cut sections. Cleaning Clean the appliance after every use. Never use scouring pads, abrasive cleaning agents or aggressive liquids such as alco...