Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
Charging Do not charge the appliance for more than 24 hours. Charging takes approx. 8 hours. When the appliance is fully charged, it has an operating time of 40 minutes. 1 Make sure the appliance is switched off. 2 Insert the appliance plug into the appliance (Fig. 2). 3 Put the adapter in the wall socket. ,, The CHARGE light goes on to indicate that the appliance is charging. Note: The CHARGE light does not indicate when the appliance is fully charged. Optimising the lifetime of the rechargeable batteries Discharge the rechargeable batteries completely twice a year by letting the motor run until it stops. Then fully recharge the batteries. Corded clipping If the batteries are low, you can also use the appliance from the mains. Only use the appliance from the mains when the rechargeable batteries are almost empty. 1 Switch off the appliance. 2 Connect the appliance to the mains and wait a few seconds before you switch it on. If the rechargeable batteries are completely empty, wait a few minutes before you switch on the appliance. Using the appliance Clipping with hair clipping comb Note: Make sure your hair is clean and dry. Do not use the appliance on freshly washed hair. QC5135 4222.002.8136.2 Register your product and get support at 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 1 2 1 2 Comb your hair with a styling comb in the direction of hair growth. (Fig. 3) Slide the hair clipping comb into the guiding grooves of the appliance (‘click’) (Fig. 4). Make sure that the arms of the comb have been properly slid into the grooves on both sides. 3 Press the length setting selector (1) and then move the hair clipping comb up or down (2) to set the desired length setting (Fig. 5). The corresponding hair length is visible on , the side of the comb. length settings With the hair clipping comb attached, the appliance can cut hair to 10 different lengths: Hair lengths in mm Hair lengths in inches 5 7 9 11 13 15 17 19 21 3 1/8 3/16 9/32 3/8 7/16 1/2 5/8 21/32 3/4 7/8 4 5 Slide the on/off slide upwards to switch on the appliance (Fig. 6). Place the hair clipping comb on the scalp and move the appliance through the hair slowly. Tips -Star t clipping at the highest length setting of the hair clipping comb and reduce the length setting gradually. -Write down the length settings you have used to create a cer tain hairstyle as a reminder for future clipping sessions. -To clip in the most effective way, move the appliance against the direction of hair growth. -Since hair grows in different directions, you need to move the appliance in different directions as well (upward, downward or across) (Fig. 7). -Make overlapping passes over the head to ensure that the appliance catches all the hairs that need to be cut. -Make sure that the flat par t of the hair clipping comb is fully in contact with the scalp to obtain an even clipping result. - - To achieve a good result with curly, sparse or long hair, you can use a styling comb to guide the hair towards the appliance. Regularly remove cut hair from the hair clipping comb. If a lot of hair has accumulated in the comb, remove it from the appliance and blow and/or shake the hair out of it. Clipping without hair clipping comb You can use the appliance without hair clipping comb to clip your hair ver y close to the skin, to a length of 1mm (1/32 in) to contour the neckline and the area around the ears. 1 To remove the hair clipping comb, press the length setting selector (1), move the comb upwards and then pull it off the appliance (2). (Fig. 8) 2 Comb the hair ends over the ears before you start to contour the hairline. 3 Slide the on/off slide upwards to switch on the appliance (Fig. 6). 4 Tilt the appliance in such a way that only one edge of the cutting element touches the hair ends. (Fig. 9) 5 Only cut the hair ends.The hairline has to be close to the ear. 6 To contour the neckline and the sideburns, turn the appliance and make downward strokes (Fig. 10). 7 Move the appliance slowly and smoothly. Follow the natural hairline. Cleaning Never use compressed air, scouring pads, abrasive cleaning agents or aggressive liquids such as alcohol, petrol or acetone to clean the appliance. Only clean the appliance and the adapter with the cleaning brush supplied. Do not use any sharp objects to clean the appliance. Clean the appliance after ever y use. 1 Make sure the appliance is switched off and disconnected from the mains. 2 To remove the comb, press the length setting selector (1), move the comb upwards and then pull it off the appliance (2). (Fig. 8) 3 Push the middle part of the cuttingunit upwards with your thumb until it opens (Fig. 11). 4 5 6 Clean the cutting unit with the cleaning brush supplied (Fig. 12). Clean the inside of the appliance with the cleaning brush supplied (Fig. 13). Clean the hair clipping comb with the cleaning brush supplied. Note:The appliance does not need any lubrication. Replacement To buy accessories or spare par ts, visi...