Assessments - 2, GPA: 3
(
)
)
|
Facilidade de uso
BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE, CATALOG NO., TYPE NO., AND DATE CODE. IN MOST CASES, A BLACK & DECKER REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER. (544-6986) Cord Lock Fork Dispositif de verrouillage de la rallonge Seguro para el cable 5°-10° Date Code: 14 • WARNING: The guard must always be on the tool to protect the user. NEVER OPERATE TOOL WITHOUT GUARD FIRMLY IN PLACE. UNPLUG THE TOOL BEFORE ATTEMPTING TO ATTACH THE GUARD. 1. Position the open center of the guard over the line feed head (Figure 1). 2. Hinge the guard on the hook located on the lower motor housing. Ensure the line is free, and not tucked under the guard. Once hooked, lightly pull on the back edge of the guard and push the guard down until the 3 latches snap into place on the motor housing. (Figure 2) ASSEMBLY / ADJUSTMENT SET-UP 15 Minimum Gage for Cord Sets Volts Total Length of Cord in Feet 120V 0-25 26-50 51-100 101-150 240V 0-50 51-100 101-200 201-300 Ampere Rating More Not more American Wire Gage Than Than 0 - 6 18 16 16 14 6 - 10 18 16 14 12 10- 12 16 16 14 12 12- 16 14 12 Not Recommended 3. The guard is not intended to be removed once installed. 4. Once the guard is installed, remove the covering from the line cut-off blade, located on the edge of the guard. 5. The auxiliary handle can be adjusted along the tube. Simply loosen the knob and position the handle as desired. Retighten knob to secure the auxiliary handle. (Figure 3) 6. The GH600 allows you to adjust the length of the tube. Loosen the knob located on the auxiliary handle. CCCCoooouuuuppppeeee----bbbboooorrrrdddduuuurrrreeee GGGGHHHH666600000000 Next, adjust the height of the main handle by pushing the button and moving the handle up or down as shown in figue 11. Finally, adjust the location of the auxiliary handle as required (figure 3), securing it in place by retightening the knob. 7. Secure the extension cord with the cord retainer as shown in Figure 4. 8. Plug the extension cord into the unit. Push the cord lock fork forward, until the plug on the extension cord is secured as shown in Figure 5. To disengage the cord lock fork, push the black button on the left side of the handle while pulling the fork backwards. OPERATING INSTRUCTIONS • CAUTION: ALWAYS WEAR EYE PROTECTION • CAUTION: Inspect area to be trimmed and remove any wire, cord, or string-like objects which could become entangled in the rotating line or spool. Be particularly careful to avoid any wire which might be bent outwardly into the path of the tool, such as barbs at the base of a chain link fence. • With the unit on, slowly swing the trimmer side to side as shown in Figure 7. • To convert for maintenance edging, unplug the unit from the power source. Gently pull the wire edge guide down into place as shown in Figure 8. Push the black “For Edging” button and rotate the lower motor housing 180°. The tool will lock in the edger position. • To operate as a maintenance edger, position the trimmer above the surface as shown in Figure 10. • Return to the trimming position by unplugging the unit from the power source, pushing the black “For Edging” button and rotating the lower motor housing back 180°. The tool will lock in the trimmer position. When using the tool put up the wire edge guide to the original position, out of the way. CUTTING LINE LINE FEEDING Your trimmer uses .065” (1.65 mm) diameter, ROUND nylon line to cut grass and weeds quickly and easily. During use, the tip of the nylon line will become frayed and worn and the special self feeding line hub will automatically feed and trim a fresh length of line. Cutting line will wear faster and require more feeding if the cutting or edging is done along sidewalks or other abrasive surfaces or heavier weeds are being cut. The advanced automatic line feeding mechanism senses when more cutting line is needed and feeds and trims the correct length of line whenever its required. DO NOT BUMP unit on ground in attempt to feed line or for any other purposes. CLEARING JAMS AND TANGLED LINES From time to time, especially when cutting thick or stalky weeds, the line feeding hub may become clogged with sap or other material and the line will become jammed as a result. To clear the jam, follow the steps listed below. 1. Unplug the trimmer. 2. Press the release tabs on the line hub cap, as shown in Figure 12 and remove the cap by pulling it straight off. 3. Lift the spool of nylon line out of the hub and clear any broken line or cutting debris from the spool area. (If you plan to replace the spool or rewind it, this is the place to do so, otherwise, move on.) 4. Unwrap about one foot (30 cm) of line to ensure that it’s undamaged. If it is OK rewind it and insert the line end through the eyelet in the spool hub as shown in Figure 13. Pull 4” (10 cm) of the line through the hole and maintain tension while placing the spool down into th...