Assessments - 1, GPA: 3
(
)
)
|
Facilidade de uso
Shorter users adjust handle to a lower position (away from you) and taller users, adjust handle to an upper position (towards you). The handle should be adjusted so that your front arm is straight when the trimmer is in the working position. HEIGHT ADJUSTMENT The overall height of the trimmer can be adjusted by loosening the lock collar and rotating it opposite to the arrow shown in figure G. The tubes can then be extended shorter or longer. When the desired height is achieved tighten the collar by rotating in the direction shown in figure G. OPERATING INSTRUCTIONS • WARNING: Always use proper eye protection that conforms to ANSI Z87.1 (CAN/CSA Z94.3) while operating this power tool. • CAUTION: Inspect area to be trimmed and remove any wire, cord, or string-like objects which could become entangled in the rotating line or spool. Be particularly careful to avoid any wire which might be bent outwardly into the path of the tool, such as barbs at the base of a chain link fence. E D G C F 8 9 ASSEMBLY INSTRUCTIONS Before assembling your Cordless String Trimmer, check that you have received the following in the shipping carton. 1. Guard 4. Auxiliary Handle 2. Charger 5. Trimmer 3. Battery Pack (1) ASSEMBLY WARNING: Remove battery pack from tool before attempting to attach the guard or make any adjustment. NEVER OPERATE TOOL WITHOUT GUARD FIRMLY IN PLACE. The guard must always be on the tool to protect the user. ATTACHING THE GUARD • Remove the screw from the bottom of the guard. • Insert the guard into the motor housing (figure B) until it “snaps” into place. • Reinsert the screw through the hole in the guard and tighten as shown in figure C. 1 4 5 3 2 24v B 90563738 NST1024.qxd: chainsaw booklet new 5/25/10 1:13 PM Page 8 10 LINE FEEDING Your trimmer uses .065 in. (1.65mm) diameter nylon line to cut grass and weeds quickly and easily. In time, the tip of the nylon line will become worn and the auto feed mechanism will automatically feed and trim a fresh length of line. The cutting line will wear faster if the cutting is done along sidewalks or other abrasive surfaces or heavier weeds are being cut. The automatic feed mechanism senses when more cutting line is needed and feeds and trims the correct length of line whenever it is required. Do not bump unit on ground in attempt to feed line or for any other purpose. REPLACING SPOOL Black & Decker recommends that for optimal performance, use only Black & Decker replacement spools (AF-100) which can be purchased at many local tool retailers. If you need assistance regarding accessories call 1-800-544-6986. • Turn off the trimmer and remove the battery. • Press the release tabs on the line spool cover, as shown in figure N and remove the cover by pulling it straight off. • Lift the spool of nylon line out of the hub and clear any broken line or cutting debris from the spool area. • Rotate the wire edge guide forward and down into place before edging, as shown in figure L. • To operate as a maintenance edger, position trimmer above sidewalk or other surface as shown in figure M. • To return to the trimming position, turn the tool off, push in on the release button and rotate the trimmer head counter clockwise until it stops. When using the tool in the trimmer mode you may choose to fold the wire edge guide up out of the way. 11 M L N RC-100-P Cap • To turn the tool off, release the trigger. • Hold trimmer with two hands and slowly swing trimmer side-to-side as shown in figure J. POWER COMMAND TM FEATURE The Power Command feature (3) is located on the tool handle as shown in figure I. It allows you to optimize the tools performance and boost the power as needed. • Operate in “Normal” mode for most trimming needs. (Longer runtime will be achieved.) • Switch to “Boost” mode on the fly when tall, wet or thick conditions are present. EDGING MODE • WARNING: Remove battery pack from tool before attempting to make any adjustment. To convert for maintenance edging: • Hold the trimmer with one hand and grasp the housing. • Push in on the release button (as shown in figure K ) and rotate the trimmer head until it stops, (half turn). • Release your hand. The tool is locked in the edger position. OPERATING THE TRIMMER • Insert the fully charged battery into the trimmer until you hear it “click” into place as shown in figure H. • To turn the trimmer on, push the lock off button (1), across and, then squeeze the trigger switch (2) shown in figure I. In a few seconds or less you.ll hear the nylon line being cut automatically to the proper length. H J POWER COMMAND TM NORMAL BOOST K I 2 1 3 90563738 NST1024.qxd: chainsaw booklet new 5/25/10 1:13 PM Page 10 90563738 NST1024.qxd: chainsaw boklet 5/25/10 1:13 PM Page 1 2 • In case of jams and tangled tangled more frequently than Black & Decker factory wound spools. CLEANING has established programs in the United States and Canada to line unwrap about one foot Black & Decker recommends to use factory wound spools for optimal • Use only mild...
Este manual também é adequado para os modelos :Clippers - AF-100 (973.16 kb)