Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
Tighten the screw. The screw will firmly retain the guard to your trimmer. 4. The guard is not intended to be removed. 5. Secure the extension cord with cord retainer as shown in Figures 4 and 5. 6. The auxiliary handle can be located all around the tube. Simply loosen the knob and position the handle as desired. ASSEMBLY / ADJUSTMENT SET-UP OPERATING INSTRUCTIONS • CAUTION: ALWAYS WEAR EYE PROTECTION • CAUTION: Inspect area to be trimmed and remove any wire, cord, or string-like objects which could become entangled in the rotating line or spool. Be particularly careful to avoid any wire which might be bent outwardly into the path of the tool, such as barbs at the base of a chain link fence. 1. Angle unit as shown in Figure 6. 2. Slowly swing trimmer side to side, as shown in Figure 7. 3. To convert for maintenance edging (Figure 8) unplug from power source, depress conversion button and rotate the motor housing. 4. When the button snaps back into place the tool is locked in the edger position. 5. Return to trimming position by unplugging the tool, depressing the button and rotating back. 6. To operate as a maintenance edger, position tool above sidewalk, as shown in Figure 9. Rest edge guide as shown. Cutting Line LINE FEEDING Your trimmer uses .065” (1.65 mm) diameter, ROUND nylon line to cut grass and weeds quickly and easily. During use, the tip of the nylon line will become frayed and worn and the special self feeding line hub will automatically feed and trim a fresh length of line. Cutting line will wear faster and require more feeding if the cutting or edging is done along sidewalks or other abrasive surfaces or heavier weeds are being cut. The advanced automatic line feeding mechanism senses when more cutting line is needed and feeds and trims the correct length of line whenever its required. DO NOT BUMP unit on ground in attempt to feed line or for any other purposes. CLEARING JAMS AND TANGLED LINES From time to time, especially when cutting thick or stalky weeds, the line feeding hub may become clogged with sap or other material and the line will become jammed as a result. To clear the jam, follow the steps listed below. 1. Unplug the trimmer. 2. Press the release tabs on the line hub cover, as shown in Figure 10 and remove the cover by pulling it straight off. 3. Lift the spool of nylon line out of the hub and clear any broken line or cutting debris from the spool area. (If you plan to replace the spool or rewind it, this is the place to do so, otherwise, move on.) 4. Unwrap about one foot (30 cm) of line to ensure that it’s undamaged. If it is OK rewind it and insert the line end through the eyelet in the spool hub as shown in Figure 11. Pull the line through the hole to maintain tension while placing the spool down into the hub with the arrow up, as shown in Figure 12. 5. Press the spool down GENTLY and rotate it until you feel it drop into place. (When in place, the spool will turn a few degrees left and right freely). Take care to keep the line from becoming trapped under the spool. 6. Snap the hub cover back on, and turn the tool on. In a few seconds or less you’ll hear the nylon line being cut automatically to the proper length. SPOOL OR LINE REPLACEMENT (Use .065” diameter ROUND line only) 1. Perform steps 1 and 2 above. 2. Remove the spool from the tool and remove and discard all line on the spool. 3. Choose either OPTION 1 or OPTION 2 below for spool or line replacement. 4. Insert the line end through the eyelet in the spool hub, as shown in Figure 12. Pull the line through the hole to maintain tension while placing the spool down into the hub, as shown. 5. Press the spool down GENTLY and rotate it until you feel it drop into place. (When in place, the spool will turn a few degrees left and right freely). Take care to keep the line from becoming trapped under the spool. 6. Snap the hub cap and spring back on, and power the tool on. In a few seconds or less you’ll hear the nylon line being cut automatically to the proper length. OPTION 1: ACCESSORY REPLACEMENT SPOOL Use Black & Decker replacement spool Model No. AF-100. OPTION 2: REWINDING SPOOL USING BULK LINE Bulk line for your trimmer/edger is available at extra cost from your local dealer or Black & Decker Service Center. To install bulk line, follow the steps below. (Use .065” diameter ROUND line only) 1. Insert one end of the bulk line into the hole in the spool as shown in Figure 13 about 1/2” (12 mm). 2. Hold the line in the hole and pull the rest of the line through the slot in the spool, shown in Figure 13. 3. Snugly and evenly wind the bulk line onto the spool in the direction of the arrow on the spool until the line builds up to the notches in the spool rim. Do not overfill spool. The spool holds 30 feet (10 m) of line.nds or less you’ll hear the nylon line being cut automatically to the proper length. Be sure the tool is unplugged. 1. Keep the air intake slots (Figure 14) clean to avoid overheating. 2. Your trimmer line can d...