Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
This can be adjusted to the operator’s preference by simply loosening the screws and sliding the handle up or down the shaft. Make sure to retighten the screws before operating hedge trimmer. Trimming Adjusting the blade angle WARNING DANGER BLADES COAST AFTER RELEASING THROTTLE OR STOPPING MOTOR. KEEP A FIRM GRIP WITH BOTH HANDS WHILE BLADES ARE MOVING AND/OR MOTOR IS RUNNING. KEEP A SURE FOOTING. DO NOT OVERREACH. IF YOUR TRIMMER BECOMES JAMMED, RELEASE SWITCH AND STOP MOTOR. MAKE SURE BLADES HAVE STOPPED COMPLETELY. UNPLUG THE UNIT, THEN REMOVE THE OBSTRUCTION. WARNING – DANGER SWITCH OFF THE MOTOR AND UNPLUG THE UNIT BEFORE LUBRICATING OR ADJUSTING THE BLADES. 1.To adjust the blade angle, first shut off the motor. Next, grip the blade adjustment handle. Then move the quick release lever from the tight position, at the right angle, so that it is pointing straight out. WARNING – DANGER DO NOT ADJUST BLADE ANGLE BY GRASPING THE BLADES. BLADES ARE SHARP AND YOU RISK INJURY TO YOURSELF. 1. Do not start the motor until you are familiar with your hedge trimmer and all of its controls and functions. 2. Plug in the unit and grasp the handles securely. One hand grasps the front loop handle, while the other hand grasps the switch handle. With both hands on the handles, push lockout trigger button with your thumb and then squeeze trigger to engage the blades. Start cutting when motor runs at full RPM. 0.3 cm 0.6 cm Lockout trigger button Trigger 1.25 cm 3. Tilt the trimmer so the cutting teeth are angled slightly toward the hedge or shrub and proceed to cut. Use overlapping sweeping motions away from your body to achieve a safe and even cut. 4. This unit is designed to cut any type of hedge or shrub with a branch thickness under 1/2” in (13 mm) diametre (see below). The depth of each cut depends on the hardness of the wood. THICKNESS OF CUT SHOULD NOT EXCEED 13mm (1/2 inch) IN DIAMETRE. Misuse of this hedge trimmer will void the warranty, i.e.: Cutting hedges or shrubs over 13mm (1/2”) diametre or foreign objects such as wires, rocks or fences. Before trimming, check work area for foreign objects such as wires, cords, glass, fences, or rocks. Be sure to remove any foreign objects from the work area. Failure to properly maintain this hedge trimmer will void the warranty. 2. The blade will now adjust freely to any position up to 180°. 3. Use the adjustment handle located beneath the assembly to move the blade to the desired angle position. 4. Once the desired angle has been achieved, simply move the quick release lever back to the tight position. Quick release lever Blade adjustment handle WARNING – DANGER DO NOT OPERATE UNIT UNLESS QUICK RELEASE LEVER IS IN THE “TIGHTENED” POSITION. WARNING – DANGER SWITCH OFF THE ENGINE BEFORE LUBRICATING OR ADJUSTING THE BLADES. WARNING – DANGER SWITCH OFF THE ENGINE BEFORE LUBRICATING OR ADJUSTING THE BLADES. Notes Blades adjustment The care and adjustment of the blades is very important to the efficient operation of the trimmer and especially to the long life of the motor. When resting, it is often a good idea to use the time to oil the cutting blades. If a gap exists between the upper and lower blades, follow the procedure below to adjust them so that they fit more closely together. 1. Loosen lock nut. 2. Tighten screw fully, and then turn o...
Este manual também é adequado para os modelos :Clippers - Hedge Trimmer E System (2.42 mb)
Clippers - Hedge Trimmer E System (2.42 mb)
Clippers - Hedge Trimmer E System (2.42 mb)
Clippers - Hedge Trimmer E System (2.42 mb)