Log:
Assessments - 2, GPA: 3.5 ( )

Instruções de Operação Homelite, Modelo MIGHTYLITE UT21506

Fabricante : Homelite
Arquivo Tamanho: 3.45 mb
Arquivo Nome : 6d090699-2215-430d-ae80-c63af888e24d.pdf
Língua de Ensino: en
Ir para baixar



Facilidade de uso


Pre-mix unleaded gasoline and 2-cycle engine lubricant in a clean 1 gallon container approved for gasoline. Recommended fuel: This engine is certified to operate on unleaded gasoline intended for automotive use. Mix Homelite Premium Exact Mix lubricant with gasoline according to the instructions on the package. If Premium Exact Mix lubricant is not available, use a high quality synthetic 2-cycle engine lubricant, mixed at 2.6 oz. per gallon (US). Do not use automotive lubricant or 2-cycle outboard lubricant. NOTE: Premium Exact Mix fuel mix will stay fresh up to 30 days. DO NOT mix quantities larger than usable in a 30 day period. PREMIUM EXACT MIX (50:1) GASOLINE LUBRICANT 1 gallon (US) 2.6 oz. 1 Liter 20 cc (20 ml) FILLING TANK • Clean surface around fuel cap to prevent contamination. • Set trimmer on its side so that the spout points up. • Loosen fuel cap slowly. Rest the cap on a clean surface. • Carefully pour fuel into the tank. Avoid spillage. • Immediately replace fuel cap and hand tighten. Wipe up any fuel spillage. NOTE: It is normal for smoke to be emitted from a new engine after first use. WARNING: Always shut off engine before fueling. Never add fuel to a machine with a running or hot engine. Move at least 30 ft. from refueling site before starting engine. Do not smoke! Page 10 Page 11 STARTING AND STOPPING See Figures 7 - 8. Trimmer should be on a flat, bare surface for starting. The starting method differs depending on whether the engine is cold or warm. To start a cold engine: . Slowly press the primer bulb seven (7) times. . Rotate the choke dial clockwise to the FULL CHOKE position. . Squeeze throttle trigger fully and continue to hold through remaining steps. . Pull the starter grip sharply until engine attempts to run (no more than 4 pulls). . Rotate the choke dial counterclockwise to the HALF CHOKE position. . Pull the starter grip sharply until the engine runs. . Allow the engine to run for 10 seconds. . Rotate the choke dial counterclockwise to the RUN position. To start a warm engine: . Slowly press the primer bulb seven (7) times. . Pull the starter grip sharply until the engine runs. TO STOP THE ENGINE: See Figure 8. Release the throttle trigger and press and hold stop on the engine switch. if assistance is required STARTING THIS product: Do not return this product to the retail store where it was purchased. Please call our Customer Service Department for any issues you may have. For Help Call: 1-800-242-4672 OPERATING THE TRIMMER See Figure 9. WARNING: Always position the unit on the operator’s right side. The use of the unit on the operator’s left side will expose the operator to hot surfaces and can result in possible burn injury. WARNING: To avoid burns from hot surfaces, never operate unit with the bottom of the engine above waist level. OPERATION Fig. 7 throttle trigger primer bulb primer bulb Fig. 8 full choke half choke run ENGINE switch choke dial starter grip ENGINE switch Hold the trimmer with your right hand on the rear handle and your left hand on the front handle. Keep a firm grip with both hands while in operation. Trimmer should be held at a comfortable position with the rear handle about hip height. Always operate trimmer at full throttle. Cut tall grass from the top down. This will prevent grass from wrapping around the shaft housing and string head which may cause damage from overheating. If grass becomes wrapped around the string head, STOP THE ENGINE, disconnect the spark plug wire, and remove the grass. Prolonged cutting at partial throttle will result in lubricant dripping from the muffler. Page 12 OPERATION Fig. 9 proper operating WARNING: position Always hold the string trimmer away from your body, keeping clearance between your body and the product. Any contact with the housing or string trimmer cutting head can result in burns and/or other serious personal injury. CUTTING TIPS See Figures 9 - 10. . Avoid hot surfaces by always keeping the tool away from your body. (Proper operating position shown in figure 9.) . Keep the trimmer tilted toward the area being cut; this is the best cutting area. . The curved shaft trimmer cuts when passing the unit from right to left. The straight shaft trimmer cuts when passing the unit from left to right. This will avoid throwing debris at the operator. Avoid cutting in the dangerous area shown in figure 10. . Use the tip of string to do the cutting; do not force string head into uncut grass. . Wire and picket fences cause extra string wear, even breakage. Stone and brick walls, curbs, and wood may wear string rapidly. . Avoid trees and shrubs. Tree bark, wood moldings, siding, and fence posts can easily be damaged by the string. ADVANCING STRING USING THE EZ wind™ Tap Advance System String advance is controlled by tapping string head on grass while running engine at full throttle. . Run engine at full throttle. . Tap string head on ground to advance string. String advances each time the head is tapped. . Several taps may ...

Este manual também é adequado para os modelos :
Clippers - MIGHTYLITE UT21546 (3.45 mb)
Clippers - MIGHTYLITE UT21907 (3.45 mb)
Clippers - MIGHTYLITE UT21947 (3.45 mb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias