Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. WWW sears+corn/craftsman Form No. JAN 02 Warranty ..................................... 2 Safety Instructions .......................... 2 Operation ............................................ 3 Maintenance ................................................... 6 Service ........................................................................ 6 Storage ...................................................................... 6 Accessories .....

5. Connect wire to plug. 6. Replace spark plug. 7. Move throttle lever to FAST position. 1. Clean/replace a_r filter. 2. Clean underside of trimmer and trimmer head. 3. Check oil level. 4. Trim at slower walking speed. 1. Check trimmer lines. 2. Check all hardware, including engine bolts. 3. Check/repair trimmer head. 1. Contact a Sears or other qualified service center. 1. Put belt on pulleys or replace belt if broken. 1. If line is worn or broken to half original length, replace line. 2. Move

172.74815 CHARGE BATTERY BEFORE FIRST USE CAUTION: Read, understand and follow all Safety Rules and Operating Instructions in this Manual before using this product. Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A Visit our Craftsman® website: • WARRANTY • SAFETY • ASSEMBLY • OPERATION • MAINTENANCE • PARTS LIST Warranty............................................................................................ Page 2 Safety Symbols ........................................................

358.745290 • Safety • Assembly • Operation • Maintenance • Espar_ol Read and follow all Safety Rules and Operating WARNING: Instructions before first use of this product. For answers to your questions about this product: Call 7 am-7 pm, Mon-Sat; 10 am-7 pm, Sun • 1-800-235-5878 (Hours listed are Centra, Time) Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. 530164371 11/7/03 Warranty Statement 2 Parts Available Safety Rules 2 Storage 9 AssemblyOperationMaintenance 5 6 8 Troubleshooting S

Follow instructions for service. Keep handles dry, clean, and free from oil and grease, AVOID UNINTENTIONAL STARTING -Don't carry the appliance while holding the switch area. The unit is shipped partly charged, and may start inadvertently if not handled properly. CHECK DAMAGED PARTS -If any component of the appliance experiences a hard impact, check that no parts were damaged and verify that the unit operates properly. Check for misalignment or bending of moving parts,breakage ofparts,andanyothe

1. Turn knob counterclockwise to loosen coupler (Fig. 15, p. 8). 2. While firmly holding attachment, push it straight into the coupler until the release button snaps into the primary hole (Fig. 16, p. 9). NOTE: Aligning the release button with the guide recess (Fig. 16, p. 9) will help installation. 3. Turn the knob clockwise to tighten. LINE TRIMMER APPLICATIONS Cutting grass and light weeds; edging; and decorative trimming around trees, fences, etc. Fig. 2 Line Cutting Blade Fuel Cap Fuel Cap

2. Press and hold the release button (Fig.12). 3. While firmly holding the upper shaft housing, pull the cutting attachment or add-on straight out of the coupler (Fig.12). Coupler Release Button Fig. 12 WARNING: To avoid serious injury and damage to the unit, shut off the unit before removing or installing attachments. STARTING INSTRUCTIONS 1. Check the oil level in the crankcase. Refer to Checking the Oil Level ( p.] 2). 2. Turn switch to ON position (Fig.] 4). NOTE: If your unit is equipped wi

• This unit has a clutch. The cutting attachment remains stationary when the engine is idling. If it does not, take the unit to a Sears or other qualified service dealer for an adjustment. • Adjust the D-handle to your size in order to provide the best grip. • Be sure the cutting attachment is not in contact with anything before starting the unit. • Use the unit only in daylight or good artificial light. • Avoid accidental starting. Be in the starting position whenever pulling the starter rope.

ing screen. If you operate in a locale ASSEMBLY CARTON CONTENTS Check carton contents against the following list. Model C944.514560 S Powerhead S Lower attachment (with trimmer head installed) S Cupped washer S Large nut for installing blades S Hex wrench S Handlebar S Bracket cover S Bracket cover screws (2) S Metal blade shield S Blade shield screws (4) S 4- --point weed blade S Plastic shield S Wing nut (screwed onto plastic shield) S Shoulder strap with warning S Container of oil Examine par

3). WARNING: Read and understand operator’s manual for unit to be used with this attachment prior to operation. WARNING: To avoid serious personal injury and damage to the unit, shut unit off before removing or installing attachments. Primary Hole Upper Shaft Housing Craftsman Convertible™ Coupler Fig. 2 Lower Shaft Housing Release Button Knob 4. Turn the knob clockwise to tighten (Fig. 1). CAUTION: Lock the release button in the primary hole (Fig. 2) and securely tighten the knob before operati