Allow the engine to cool before storing in any enclosure. 4. To reduce fire hazard, keep the engine free of grass, leaves, or excessive grease. 3 I ASSEMBLY INSTRUCTIONS NOTE This unit is shipped WITHOUT GASOLINE or OIL. After assembly, see operating section of this manual for proper fuel and engine oil recommendations. NOTE Any reference to right and left hand will be determined from behind the edger, in the operator's position. TOOLS REQUIRED: A (1) Adjustable Wrench. B (1) 7/16" Op

See figure 4. Secure with push cap (E) by tapping it on with a hammer. See figure 5. It is necessary to hold a block of wood or a second hammer against the push cap on the other side of the axle. 5. Secure the front wheels and axle in position using two hairpin cotters (A). See figure 5. 6. Slip the three handle grips (T) on the upper handles and the engagement handle. They will slip on more easily if you first soak them in warm, soapy water. 7. Assemble the two upper handles to the lower han

770-5200D NDEX Safe Operation Practices.....................3 Assembly Instructions.................... . . 4 Operation ............................... 7 Adjustments............................. 7 Lubrication.............................. 8 Maintenance ............................ 8 Off-Season Storage........................ 9 Trou be Shooting Chart.................... 9 Illustrated Parts..........................10 Replacement Parts List....................11 A Instructions given wi

Make certain that all loose parts and literature are removed from carton before carton is discarded. 4 FIGURE 3. 2. Place lower handle into the slots in the rear frame. See figure 3. 3. Line up holes in handle with holes in frame. See figure 3. 4. Secure rear wheels (W) and lower handle (T) to frame with shoulder bolts (A), belleville washers (B) (cupped side of washer against the frame), lock washers (C) and hex nuts (D). See figure 3. FRONT WHEEL BELLEVILLE WASHER (B) HEX NUT. '(D) 5

Be careful of the staples. Make certain all parts and literature have been removed from the carton before the carton is discarded. 2. Disconnect and ground the spark plug wire against the engine. 3. Stretch out the throttle control cable and place on the floor. Be careful not to bend or kink tb cable at any time during assembly. 4. Separate the contents of the hardware pack according to the illustration above for identification purposes. 4 Hole and Slot in Frame mk Lock Washer FIGURE 1

Pour slowly. See figure 15. 2. Fill the fuel tank with clean, fresh, lead-free, low lead, or regular grade leaded gasoline. DO NOT MIX OIL WITH GASOLINE. 3. Move the engagement handle (depth control) back as far as it will go and place in the last notch. See figure 12. 4. Set the throttle control in "START” position. 5. Pull the choke knob out. NOTE A warm engine may not require choking. 6. Grasp the starter handle and pul! out the cord rapidly. Return it slowly to the engine. If the engi

Using a light oil or silicone, coat the equipment, especially springs and bearings. 10 TROUBLE SHOOTING CHART k PROBLEM CAUSE (S) CORRECTIVE ACTION(S) 1. Engine fails to start. A. Check fuel tank for gas. B. Spark plug lead wire disconnected. C. Faulty spark plug. A. Fill tank if empty. B. Connect lead wire. C. Spark should jump gap between control electrode and side electrode. If spark does not jump, replace the spark plug. 2. Hard starting or loss of power. A. Spark plug wire loose. B. Di

Ref. no. 58. Wheel Vertical Adjustment - By releasing the leve' on the R.H. side of the frame, you can raise anc lower the front wheel of your edger. Additional adjustment can be made by unscrewing the axle bolt and using the different holes in the end of the wheel bracket assembly. Ref. no. 24. By becoming familiar with all the controls and adjustments before you operate your edger, you will be able to easily adjust your edger to a variety of cutting and trimming conditions. While the engine

x .060 12 714-0105 Sq.Key 3/16 x 1.0" Lg.* 47 710-0623 Hex Wash. Hd. Self Tap Scr. 13 710-0938 Set Scr. 1/4-28 x 1/4" Lg. Hex Bolt 5/16-18 x 1.50* Lg.* 3/8-16 x .75" Lg. 14 710-0442 48 738-0108 Shoulder Bolt .498" Dia. x 15 711-0421 Engine Pulley 1.450 16 08253 Bearing Housing 49 734-1176 Wheel Ass'y. Comp. 7" Dia. 17 736-0242 Bell.-Wash. .34" I.D. x 88" x 1.50 O.D. x .060 50 736-0105 Bell.-Wash. .400" I.D. x 88" 18 710-0528 Hex Bolt 5/16-18 x 1.25"

Allow the engine to cool before storing in any enclosure. 4. To reduce fire hazard, keep the engine free of grass, leaves, or excessive grease. 3 I CONTENTS OF HARDWARE PACK ATTACHING THE LOWER HANDLE AND REAR WHEELS. Shoulder Bolt — Cupped Washer 1/2" I.D. Hex Lock Nut -3/8-16 Thread Axle Bolts' Cupped Washer 3/8" I.D.- Flat Washer 3/8" I.D.-Lock Washers 3/8" I.D.-* Hex Nuts 3/8-16 Thread ATTACHING THE ENGAGEMENT HANDLE AND CLUTCH ROD Cotter. Pins Rod Adjustment Link Hex Bolt 5/