Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
(Note 2) Due to standard PC architecture, a certain amount of memory is reserved for system usage and therefore the actual memory size is less than the stated amount. For example, 4 GB of memory size will instead be shown as 3.xxGB memory during system startup. (Note 3) To use a DDRII 667 memory module on the motherboard, you must install an 800/1066MHz FSB processor . Only for GA-8I945G Pro. Only for GA-8I945G. GA-8I945G Pro/GA-8I945G Motherboard - 10 English Onboard Audio • ALC882 CODEC • High Definition Audio • Supports 2 / 4 / 6 / 8 channel audio • Supports Line In ; Line Out (Front Speaker Out) ; MIC ; Surround Speaker Out (Rear Speaker Out) ; Center/Subwoofer Speaker Out ; Side Speaker Out connection • SPDIF In connection • SPDIF Out connection (coaxial+optical) • CD In • Supported on the Win 2000/XP operating systems On-Board SATA 3Gb/s • Onboard ICH7R chipset RAID • supports data striping (RAID 0) or mirroring (RAID 1) function or striping + mirroring (RAID 0+1) or RAID 5 function • supports data transfer rate of up 300 MB • supports a maximum of 4 SATA 3Gb/s connections • supported on the Win 2000/XP operating systems On-Board IDE RAID • Onboard GigaRAID IT8212 chipset (IDE2, IDE3) • Supports disk striping (RAID 0) or disk mirroring (RAID 1) or striping + mirroring (RAID 0 + RAID 1) • Supports JBOD function • Supports concurrent dual ATA133 IDE controller operation • Supports ATAPI mode for HDD • Supports IDE bus master operation • Supports ATA133/RAID mode switch by BIOS • Displays status and error checking messages during boot-up • Mirroring supports automatic background rebuilds • Features LBA and Extended Interrupt 13 drive translation in controller onboard BIOS I/O Control • IT8712 Hardware Monitor • System voltage detection • CPU temperature detection • CPU / System / Power fan speed detection • CPU warning temperature • CPU / System / Power fan failure warning • CPU smart fan control BIOS • Use of licensed AWARD BIOS • Supports Q-Flash/Dual BIOS /Multilanguage Additional Features • Supports @BIOS • Supports EasyTune 5 Overclocking • Over Voltage via BIOS (CPU/DDR/PCIE/FSB) • Over Clock via BIOS (CPU/DDR) Form Factor • ATX form factor; 30.5cm x 22.0cm Only for GA-8I945G Pro. -11 - Hardware Installation English Fig. 3 Fig. 4 Notice the small gold Once the CPU is colored triangle located properly inserted, on the edge of the CPU please replace the socket. Align the load plate and indented corner of the push the metal lever back into its original CPU with the triangle and gently insert the CPU into position. position. (Grasping the CPU firmly between your thumb and forefinger, carefully place it into the socket in a straight and downwards motion. Avoid twisting or bending motions that might cause damage to the CPU during installation.) 1-3 Installation of the CPU and Heatsink Before installing the CPU, please comply with the following conditions: 1. Please make sure that the motherboard supports the CPU. 2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong direction, the CPU will not insert properly. If this occurs, please change the insert direction of the CPU. 3. Please add an even layer of heat sink paste between the CPU and heatsink. 4. Please make sure the heatsink is installed on the CPU prior to system use, otherwise overheating and permanent damage of the CPU may occur. 5. Please set the CPU host frequency in accordance with the processor specifications. It is not recommended that the system bus frequency be set beyond hardware specifications since it does not meet the required standards for the peripherals. If you wish to set the frequency beyond the proper specifications, please do so according to your hardware specifications including the CPU, graphics card, memory, hard drive, etc. HT functionality requirement content : Enabling the functionality of Hyper-Threading Technology for your computer system requires all of the following platform components: - CPU: An Intel® Pentium 4 Processor with HT Technology - Chipset: An Intel® Chipset that supports HT Technology - BIOS: A BIOS that supports HT Technology and has it enabled - OS: An operation system that has optimizations for HT Technology 1-3-1 Installation of the CPU Metal Lever Fig. 1 Fig. 2 Gently lift the metal Remove the plastic lever located on the covering on the CPU CPU socket to the socket. upright position. GA-8I945G Pro/GA-8I945G Motherboard - 12 1-3-2 Installation of the Heatsink Male Push Pin The top of Female Push Pin Female Push Pin Fig.1 Fig. 2 Please apply an even layer of heatsink paste on (Turning the push pin along the direction of arrow is the surface of the installed CPU. to remove the heatsink, on the contrary, is to install.) Please note the direction of arrow sign on the male push pin doesn't face inwards before installation. (This instruction is only for Intel boxed fan) Fig. 3 Fig. 4 Place the heatsink atop the CPU and make sure Please make sure the Male and Female p...