Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Motherboard - GA-8IG1000 Pro-G (7.69 mb)
Motherboard - GA-8IG1000 Pro-G (6.33 mb)
Facilidade de uso
(*..) (*) For GA-8IG1000 Pro-G only. (..) For GA-8IG1000-G only. GA-8IG1000 Series Motherboard - 18 • Parallel Port, Serial Port and VGA Port (LPT/COMA/VGA) Parallel Port This connector supports 1 standard COM port, (25 pin Female) 1 Parallel port and 1 VGA port. Device like printer can be connected to Parallel port; mouse and modem etc can be connected to Serial ports. COMA VGA Serial Port VGA Port (9 pin Male) (15 pin Female) • Audio Connectors After install onboard audio driver, you may connect speaker to Line Out jack, microphone to MIC In jack. Devices like CD-ROM, walkman etc. can be connected to Line-In jack. Line In(Rear Speaker) Please note: You are able to use 2-/4-/6-/8-channel audio Line Out(Front Speaker) feature by S/W selection. If you want to enable 8-channel function you MIC In(Center and Subwoofer) can refer to page 27, and contact your nearest dealer for optional SUR_CEN cable. If you want the detail information for 2-/ 4-/ 6-/ 8-channel audio setup installation, please refer to page 75. English -19 -Hardware Installation Process GA-8IG1000 Series Motherboard - 20 - English Step 4-2: Connectors & Jumpers Setting Introduction 1 3 2 8 7 6(*) 21(*) 9 19 13 16 20(*) 17 23 4 18 22 10 11 15 5(*) 14 12 24 Note: If the NorthBridge on the motherboard has a fan sink, then the motherboard contains a NB_FAN connector. 1) ATX_12V 2) ATX 3) CPU_FAN 4) SYS_FAN 5) PWR_FAN (*) 6) NB_FAN (*) 7) IDE1 / IDE2 8) FDD 9) PWR_LED 10) BAT 11) F_PANEL 12) F_AUDIO 13) SUR_CEN 14) CD_IN 15) SPDIF_IO 16) IR_CIR 17) F_USB1 / F_USB2 18) GAME 19) INFO_LINK 20) F2_1394 (*) 21) F1_1394 (*) 22) SATA0 / SATA1 23) CI 24) CLR_CMOS (*) For GA-8IG1000 Pro-G only. - 21 - Hardware Installation Process English 3 1 4 2 1 20 10 11 1) ATX_12V (+12V Power Connector) This connector (ATX_12V) supplies the CPU operation voltage (Vcore). If this "ATX_12V connector" is not connected, system cannot boot. 2) ATX (ATX Power) AC power cord should only be connected to your power supply unit after ATX power cable and other related devices are firmly connected to the mainboard. Pin No. Definition 1 GND 2 GND 3 +12V 4 +12V Pin No. Definition 1 3.3V 2 3.3V 3 GND 4 VCC 5 GND 6 VCC 7 GND 8 Power Good 9 5V SB (stand by +5V) 10 +12V 11 3.3V 12 -12V 13 GND 14 PS_ON(soft on/off) 15 GND 16 GND 17 GND 18 -5V 19 VCC 20 VCC GA-8IG1000 Series Motherboard - 22 - English Pin No. Definition 1 GND 2 +12V 3 Sense Pin No. Definition 1 GND 2 +12V 3 Sense 3) CPU_FAN (CPU Fan Connector) Please note, a proper installation of the CPU cooler is essential to prevent the CPU from running under abnormal condition or damaged by overheating. The CPU fan connector supports Max. current up to 600 mA. 4) SYS_FAN (System Fan Connector) This connector allows you to link with the cooling fan on the system case to lower the system temperature. 1 1 - 23 - Hardware Installation Process English 5) PWR_FAN (Power Fan Connector) (*) This connector allows you to link with the cooling fan on the system case to lower the system temperature. 6) NB_FAN (*) If you installed wrong direction, the Chip Fan will not work. Sometimes will damage the Chip Fan. (Usually black cable is GND) Note: If the NorthBridge on the motherboard has a fan sink, then the motherboard contains a NB_FAN connector. (*) For GA-8IG1000 Pro-G only. Pin No. Definition 1 GND 2 +12V 3 Sense Pin No. Definition 1 GND 2 VCC 1 1 GA-8IG1000 Series Motherboard - 24 - English 7) IDE1 / IDE2 (IDE1 / IDE2 Connector) Please connect first harddisk to IDE1 and connect CDROM to IDE2. The red stripe of the ribbon cable must be the same side with the Pin1. 8) FDD (Floppy Connector) Please connect the floppy drive ribbon cables to FDD. It supports 360K,720K,1.2M,1.44M and 2.88Mbytes floppy disk types. The red stripe of the ribbon cable must be the same side with the Pin1. 1 39 2 40 IDE2 IDE1 1 34 2 33 - 25 - Hardware Installation Process English 9) PWR_LED PWR_LED is connect with the system power indicator to indicate whether the system is on/off. It will blink when the system enters suspend mode. If you use dual color LED, power LED will turn to another color. Pin No. Definition 1 MPD+ 2 MPD- 3 MPD- 10) BAT (Battery) + 1 CAUTION .. Danger of explosion if battery is incorrectly replaced. .. Replace only with the same or equivalent type recommended by the manufacturer. .. Dispose of used batteries according to the manufacturer's instructions. If you want to erase CMOS... 1.Turn OFF the computer and unplug the power cord. 2.Remove the battery, wait for 30 second. 3.Re-install the battery. 4.Plug the power cord and turn ON the computer. GA-8IG1000 Series Motherboard - 26 - English 11) F_PANEL (2 x 10 pins connector) Please connect the power LED, PC peaker, reset switch and power switch etc. of your chassis front panel to the F_PANEL connector according to the pin assignment below. HD (IDE Hard Disk Active LED) Pin 1: LED anode(+) (Blue) Pin 2: LED cathode(-) SPEAK (Speaker Connector) Pin 1: VCC(+) (Amber) Pin 2- Pin 3: NC Pin 4: Data(-) RES (R...