Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Motherboard - GA-6BXE (826.47 kb)
Motherboard - GA-6BXE (574.67 kb)
Motherboard - GA-6BXE (572.29 kb)
Facilidade de uso
-Suspend mode support. -Green switch & ACPI LED support. -IDE & Display power down support. -Monitor all IRQ / DMA / Display / I/O events. -2M bits FLASH RAM. - Supports Plug & Play, DMI , ACPI Function. -ATX Form Factor, 4 layers PCB. -INTEL Bus Master IDE Driver. -Suspend to HD utility. -INTEL LDCM®. -Licensed AWARD BIOS. -AT CMOS Setup, BIOS / Chipset Setup, Green Setup, Hard Disk Utility included. -Operation with MS-DOSa, Windowsa95, Windowsa98, WINDOWS NT™, OS/2, NOVELL and SCO UNIX. 2.3. ENVIRONMENT · Ambient Temp. -0°C to +50°C (Operating). · Relative Hum. -0 to +85% (Operating). · Altitude -0 to 10,000 feet (Operating). · Vibration -0 to 1,000 Hz. · Electricity -4.9 V to 5.2 V. (Max. 20A current at 5V.) 2-2 Hardware Installation 3. HARDWARE INSTALLATION 3.1. UNPACKING The main board package should contain the following: · The 6BXE main board. · Universal Retention Mechanism & Attach Mount · USER’ S MANUAL for main board. · Cable set for IDE, Floppy devices. · Diskette or CD for main board Utility. The main board contains sensitive electric components, which can be easily damaged by static electricity, so the main board should be left in its original packing until it is installed. Unpacking and installation should be done on a grounded anti-static mat. The operator should be wearing an anti static wristband, grounded at the same point as the anti-static mat. Inspect the main board carton for obvious damage. Shipping and handling may cause damage to your board. Be sure there are no shipping and handling damages on the board before proceeding. After opening the main board carton, extract the system board and place it only on a grounded anti-static surface component side up. Again inspect the board for damage. Press down on all of the socket IC's to make sure that they are properly seated. Do this only on with the board placed on a firm flat surface. MDO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN DAMAGED. 3-1 6BXE 3.2. MAINBOARD LAYOUT PCB Ver : 1.9 SLOT1 Intel 440BX PIIX4 6BXE COMBCOMA JP1 FLOPPYIDE1 IDE2 JP11 BANK1 BANK3 BANK0 BANK2 SW JP14 LPT JP12 BIOS JP8 J15 J8 BAT1 BZ1 JP9 J17 PCB Ver : 2.0 SLOT1 Intel 440BX PIIX4 6BXE COMBCOMA JP1 FLOPPYIDE1 IDE2 JP11 BANK1 BANK3 BANK0 BANK2 SW JP14 LPT JP12 BIOS JP8 J15 J8 BAT1 BZ1 JP9 J17 JP19 JP18 .Figure 3.1• 3-2 Hardware Installation 3.3. QUICK REFERENCE FOR JUMPERS & CONNECTORS t I/O Ports Connector USB USB port. IDE 1 For Primary IDE port. IDE 2 For Secondary IDE port. PS/2 For PS/2 Keyboard port. PS/2 For PS/2 Mouse port. Floppy For Floppy port COM B For Serial port2 (COM B). COM A For Serial port1 (COM A). ATX POWER For ATX Power Connector. LPT For LPT port. t Slot 1 For Pentiuma II / III / Celerona Processor installed t J1 :CPU FAN : CPU Cooling FAN Power Connector Pin Function 1 GND 2 +12V 3 Signal t J16:POWER FAN : POWER FAN Power Connector Pin Function 1 GND. 2 +12V 3 Signal t J17 :PANEL FAN: PANEL FAN Power Connector Pin Function 1 GND. 2 +12V 3 Signal t J15 : System After Ac Back Open Soft Off Short Full On 3-3 6BXE t JP1 : Keyboard Power On Selection Pin Function 1-2 Enabled Keyboard power on. 2-3 Disabled Keyboard power on. t JP11 : System Acceleration Pin Function 1-2 short For 100MHz Turbo and other frequencies 2-3 short For 100MHz Normal t JP7 :Wake on LAN Connector Pin Function 1 +5VSB 2 GND 3 Signal • SB-LINK (For PCI Sound Card Connector) Pin Function 1 Signal 2 GND 3 NC 4 Signal 5 GND 6 Signal t JP12 : CASE OPEN (Optional) Pin Function 1 Signal 2 GND t IR: INFRARED Connector (OPTIONAL) Pin Function 1 IR DATA OUTPUT 2 GND 3 IR DATA INPUT 4 NC 5 POWER(+) 3-4 Hardware Installation t JP18&JP19(This function is support in PCB version 2.0 and above) Pin No. t JP14 : CLEAR CMOS Pin 1-2 short Clear CMOS 2-3 short Normal Function Function Open Normal Close For Voodoo3 VGA card JP9 : 2*11PIN Jumper G-PW P+P-P-H+ GN JP9 1 1 1 1 G+ RE SPK H-GN PW : Soft Power Connector Open: Normal Operation Short: Power On/Off RE : Reset Switch Open: Normal Operation Short: For Hardware Reset System P+P-P-: Power LED PIN 1 : LED anode (+) PIN 2 : LED cathode (-) PIN 3 : LED cathode (-) SPK : External Speaker Connector + PIN 1 : VCC (+) PIN 2 : VCC 1 1 3-5 6BXE PIN 3 : Signal PIN 4 : Signal SPK : Internal Speaker Connector (Default) + PIN 1 : VCC (+) PIN 2-PIN3 : Short PIN 4 : Data (-) H+H-: IDE Hard Disk Active LED 1 1 PIN 1: LED anode (+) PIN 2: LED cathode (-) GN: Green Function Switch Open : Normal operation Short : Entering Green Mode G-G+: Green LED 1 PIN 1 : LED anode (+) PIN 2 : LED cathode (-) 3.4. DRAM INSTALLATION The main board can be installed with 16 / 32 / 64 / 128 / 256 MB 168 pins DIMM module DRAM, and the DRAM speed must be 67~100 MHz for SDRAM when system bus speed is set to 66MHz. When system bus speed is set to 100MHz, 100MHz SDRAM is required. The DRAM memory system on main board consists of bank 0, 1, 2 & bank 3. Since 168 pins DIMM module is 64 bits width, therefore 1 piece of DIMM module may match a 64 bits system. The total memory size is 1...