Assessments - , GPA:
(
)
)
Fabricante : Gigabyte
Arquivo Tamanho: 16.33 mb
Arquivo Nome :
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
por este dispositivo também tem outras instruções :
Facilidade de uso
C. Installing the CPU Cooler C-1 Before installing the CPU cooler, please first add a thin layer of heat sink paste on the surface of the CPU. Then install the cooler (refer to the installation manual for your CPU cooler). C-2 Connect the CPU cooler cable to the CPU_FAN connector located on the motherboard so that the cooler can properly function to prevent the CPU from overheating. Step 2 Installing Memory Note the orientation of the memory module. Spread the retaining clips at both ends of the memory socket. Place the memory module on the socket. As indicated in the picture on the left, place your fingers on the top edge of the memory, push down on the memory and insert it vertically into the memory socket. The clips at both ends of the socket will snap into place when the memory module is securely inserted. Step 3 Preparing the Case and Installing a Power Supply Using the GIGABYTE desktop system as the demonstration example, please first remove both sides and the lid of the case in order to install the power supply. Place the power supply in the correct place in the case and secure it with screws. Installation and placement of the power supply may differ depending on the type of case used. To ensure sufficient power can be supplied to your system, it is recommended that a power supply of good quality be used. If a power supply is used that does not provide the required power, the result can lead to an unstable or unbootable system. Step 4 Installing the Motherboard Remove the original I/O shield from the back of the case and replace it with the motherboard I/O shield. Place the motherboard within the case by positioning it into its I/O shield. Align the mounting screw holes on the motherboard with their corresponding mounting holes on the case. Secure the motherboard in place with screws. I/O Shield Step 5 Installing an Expansion Card Locate an expansion slot that supports your card and remove the slot cover from the case back panel. Then insert the expansion card into the slot. Secure the expansion card's bracket to the case back panel with a screw. • • Before purchasing an expansion card, check the length of the card, making sure it can fit into your case. • • Make sure that the expansion card is fully seated in its slot. PCI Express Graphics Card Step 6 Installing IDE and SATA Devices 6-1 Install your optical drives, such as DVD-ROM and CD-ROM drives. Remove the 5.25" drive bay cover from the front of the case. Mount the optical drive in the 5.25" drive bay and secure it with screws. Installing an Optical Drive 6-2 Install your IDE and SATA hard drives. Install the hard drive into a drive bay within the case and secure it with screws. Installing a Hard Drive • • One motherboard IDE connector can connect up to two IDE devices. Prior to installation, check the jumper settings (master and slave) on your IDE devices. • • If more than one hard drive is installed, enter system BIOS Setup to set the hard drive boot sequence. Step 7 Connecting Cables to Internal Connectors 7-1 Connect cables to internal connectors and headers on the motherboard, including IDE/SATA connectors, and front panel audio, USB, IEEE 1394 headers, etc. 7-2 Attach the front panel module (differs depending on the case design, consisting of power indicator, hard drive activity indicator, speakers, reset switch, power switch, etc.) from the case to the front panel header (F_PANEL) on the motherboard. Pin Assignments A: Pin Assignments B: MSG: Message/Power/Sleep LED PWR: Power LED PW: Power Switch SPEAK: Speaker HD: Hard Drive Activity LED RES: Reset Switch CI: Chassis Intrusion Header +MSG- +MSG- +PW- +PW- +SPEAK- +SPEAK- 20 2 19 1 +HD- -CI+ -RES+ +PWR- +HD- -RES+ NC Front Panel Header (Note) The pin assignments for the front panel header may differ by model. Refer to the motherboard user's manual for the actual pin assignments. Step 8 Connecting Peripherals Back Panel of the Case Once the steps above have been completed, connect the peripheral devices to the computer, such as the keyboard, mouse, monitor, etc. Then connect the power, turn on the system, and install all required software. Power Switch Power Supply PS/2 Keyboard Port Power Cord Connector DVI-D Port PS/2 Mouse Port D-Sub Port HDMI Port S/PDIF Connector eSATA Port IEEE 1394 Port USB Ports Audio Jacks RJ-45 LAN Port External Graphics Card - 1 - • • Die Installationsreihenfolge kann je nach Typ des verwendeten Gehauses sowie der verwendeten Gerate variieren. Die folgenden Installationsanweisungen betreffen Desktop-Systeme von GIGABYTE und dienen nur als Referenz. • • Schlagen Sie bitte ausfuhrliche technische Daten des Motherboards im beigelegten Benutzerhandbuch nach. • • Stellen Sie vor der Installation von Geraten sicher, dass Ihre Gerate mit den Anschlussen Ihres Computers kompatibel sind. • • Schalten Sie immer vor dem Installieren die Gerate und Ihren Computer aus. Trennen Sie den Rechner vom Stromnetz, um Schaden an den Geraten und den Systemkomponenten zu vermeiden. •...
Este manual também é adequado para os modelos :Motherboard - GA-X58A-UD3R (16.33 mb)
Motherboard - GA-EX58-UD4P (16.33 mb)
Motherboard - GA-EX58-UD4 (16.33 mb)
Motherboard - GA-EX58-UD3R-SLI (16.33 mb)