Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Motherboard - GA-C1037UN (10.31 mb)
Motherboard - GA-C1037UN (9.6 mb)
Motherboard - GA-C1037UN (8.83 mb)
Facilidade de uso
Options are: 128M, 256M, MAX. (Default: MAX) &&Legacy USB Support Allows USB keyboard/mouse to be used in MS-DOS. (Default: Enabled) &&EHCI Hand-off Determines whether to enable EHCI Hand-off feature for an operating system without EHCI Hand-off support. (Default: Disabled) &&Port 60/64 Emulation Enables or disables emulation of I/O ports 64h and 60h. This should be enabled for full legacy support for USB keyboards/mice in MS-DOS or in operating system that does not natively support USB devices. (Default: Disabled) &&USB Storage Devices Displays a list of connected USB mass storage devices. This item appears only when a USB storage device is installed. &&PATA Controller(JMicron JMB368 IDE Controller)jk Enables or disables the JMicron JMB368 IDE controller. This section below provides information on the device connected to. The section below provides information on the device(s) connected to this connector. (Default: IDE Mode) &&OnBoard LAN Controller (LAN1) Enables or disables the onboard LAN function. (Default: Enabled) If you wish to install a 3rd party add-in network card instead of using the onboard LAN, set this item to Disabled. &&OnBoard LAN Controller#2 (LAN2) Enables or disables the onboard LAN function. (Default: Enabled) If you wish to install a 3rd party add-in network card instead of using the onboard LAN, set this item to Disabled. ``Super IO Configuration This section provides information on the super I/O chip and allows you to configure the serial port and parallel port. &&Serial Port A (Serial Port on the Back Panel) Enables or disables the onboard serial port. (Default: Enabled) &&Serial Port B (Onboard COMB Connector) Enables or disables the onboard serial port. (Default: Enabled) &&Parallel Port Enables or disables the onboard parallel port. (Default: Enabled) &&Device Mode This item is configurable only when Parallel Port is set to Enabled. Selects an operating mode for the onboard parallel (LPT) port. Options are: Standard Parallel Port Mode (Default), EPP Mode (Enhanced Parallel Port), ECP Mode (Extended Capabilities Port), EPP Mode & ECP Mode. ``Intel(R) Smart Connect Technology &&ISCT Configuration Enables or disables Intel® Smart Connect Technology. (Default: Disabled) j Only for the GA-C1037UN. k Only for the GA-C1007UN. 2-6 Power Management &&Resume by Alarm Determines whether to power on the system at a desired time. (Default: Disabled) If enabled, set the date and time as following: Wake up day: Turn on the system at a specific time on each day or on a specific day in a month. Wake up hour/minute/second: Set the time at which the system will be powered on automatically. Note: When using this function, avoid inadequate shutdown from the operating system or removal of the AC power, or the settings may not be effective. &&ErP Determines whether to let the system consume least power in S5 (shutdown) state. (Default: Disabled) Note: When this item is set to Enabled, the following functions will become unavailable: PME event wake up, power on by mouse, power on by keyboard, and wake on LAN. &&High Precision Event Timer (Note) Enables or disables High Precision Event Timer (HPET) for Windows 8/7 operating system. (Default: Enabled) &&Soft-Off by PWR-BTTN Configures the way to turn off the computer in MS-DOS mode using the power button. Instant-Off Press the power button and then the system will be turned off instantly. (Default) Delay 4 Sec Press and hold the power button for 4 seconds to turn off the system. If the power button is pressed for less than 4 seconds, the system will enter suspend mode. &&Internal Graphics Standby Mode Allows you to determine whether to let the onboard graphics enter standby mode to decrease power consumption. (Default: Enabled) &&Internal Graphics Deep Standby Mode Allows you to determine whether to let the onboard graphics enter deeper standby mode. (Default: Enabled) &&AC BACK Determines the state of the system after the return of power from an AC power loss. Memory The system returns to its last known awake state upon the return of the AC power. Always On The system is turned on upon the return of the AC power. Always Off The system stays off upon the return of the AC power. (Default) (Note) Supported on Windows 8/7 operating system only. &&Power On By Keyboard Allows the system to be turned on by a PS/2 keyboard wake-up event. Note: To use this function, you need an ATX power supply providing at least 1A on the +5VSB lead. Disabled Disables this function. (Default) Password Set a password with 1~5 characters to turn on the system. Keyboard 98 Press POWER button on the Windows 98 keyboard to turn on the system. Any Key Press any key to turn on the system. &&Power On Password Set the password when Power On By Keyboard is set to Password. Press