Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
2. Observe work area conditions. Don’t expose to rain unless the wood is properly treated. Keep work area well lighted. 3. Keep children away. Children must never be allowed in the work area during assembly. 4. Store idle equipment. When not in use, the Patio Set must be stored in a dry location to inhibit rust and wear. 5. Use the right tool for the job. Do not attempt to force a small Patio Set to do the work of a larger Patio Set. There are certain applications for which this Patio Set was designed. It will do the job better and more safely if you do not modify this Patio Set and do not use this Patio Set for a purpose for which it was not intended. 6. Dress properly. Do not wear loose clothing or jewelry during assembly. Protective, electrically non-conductive clothes and non-skid footwear are recommended when working. Wear restrictive hair covering to contain long hair. 7. Use eye protection. Always wear ANSI approved impact safety goggles during assembly 8. Do not overreach. Keep proper footing and balance at all times. Page 2 SKU 09018 9. Maintain the Patio Set with care. Keep it clean for better and safer performance. Inspect the Patio Set periodically, and if damaged, have it repaired by an authorized technician. 10. Stay alert. Watch what you are doing, use common sense. Do not assemble the Patio Set when you are tired. 11. Check for damaged parts. Before using the Patio Set, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment and binding of moving parts; any broken parts or mounting fixtures; and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician. 12. Replacement parts and accessories. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. 13. Do not assemble the Patio Set if under the influence of alcohol or drugs. Read warning labels if taking prescription medicine to determine if your judgement or reflexes are impaired while taking drugs. If there is any doubt, do not assemble the Patio Set. 14. Choose the proper location. Set up the Patio Set on a flat, dry, level surface. 15. Be aware of weather conditions. Make sure the umbrella is tied in the closed position or removed entirely during windy weather. The wind can knock over the umbrella and table causing serious injury. 16. Maintenance. For your safety, maintenance should be performed regularly by a qualified technician. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. WARNING: The brass components of this product contain lead, a chemical known to the State of California to cause birth defects (or other reproductive harm). (California Health & Safety code 25249.5, et seq.) Unpacking When unpacking, check to make sure the parts listed on page 6 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Page 3 SKU 09018 Assembly See the Parts List/Drawing on page 6. 1. Assembling the Table Stand (#1): Use two sets of Screws (#6) on each side of the Brace (#10) to support the bottom of the Table Stand (#1). Align the Umbrella Stand (#9) next to the Brace (#10). See FIGURE 1. FIGURE 1 Table Brace (#10) Stand (#1) Umbrella Screws (#6) Stand (#9) 2. Attach the two Brackets (#11) to the underside of the Table Board (#2) using four sets of Table Screws (#5). See FIGURE 2. 3. Attach the Table Stand (#1) to the Brackets (#11) on the Table Board (#2) using two sets of Screws (#6). See FIGURES 2 & 3. Screws (#6) FIGURE 2 Table Bracket (#11) Board (#2) Table Screw (#5) FIGURE 3 Screws (#6) Page 4 SKU 09018 Assembly (continued) 4. Connect the Umbrella (#8) and the Pole (#12) using Screw (#7). Slide the FIGURE 4 Pole (#12) into the Umbrella Stand (#9). See FIGURE 4. Umbrella (#8) Screw (#7) Pole (#12) Umbrella Stand (#9) 5. Attach the Chair Board (#4) to the Chair Stand (#3) FIGURE 5 using four sets of Screws (#6). Chair Board (#4) Note: Remember to set the Patio Set up on a flat, dry, level surface. Do not deploy the Umbrella (#8) Chair Stand (#3) during windy conditions. Maintenance 1. Periodically check the hardware and tighten if necessary. 2. If you leave the set outdoors during inclement weather, it is recommended that you seal the set with a marine quality varnish or paint. Page 5 SKU 09018 Parts List Part No. Description Qty. 1 Table Stand 1 2 Table Board 1 3 Chair Stand 2 4 Chair Board 2 5 Table Screw (6mm x 35mm) 4 Sets 6 Screw (6mm x 20mm) 14 Sets 7 Screw 1 8 Umbrella 1 9 Umbrella Stand 1 10 Brace 1 11 Bracket 2 12 Pole 1 #5 #6 #7 #9 #10 #11 PLEASE READ THE FO...