Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
1 Condensed Operating Instructions .................................. pg. 2 Setting Up ............................................................................... pg. 3 Controls & Functions ........................................................... pg. 5 All Metal Mode ....................................................................... pg. 7 Iron Disc Mode ...................................................................... pg. 8 Normal Disc Mode ................................................................ pg. 9 Search Techniques ............................................................... pg. 10 Target Recovery .................................................................... pg. 12 False Signals .......................................................................... pg. 13 Battery Replacement ........................................................... pg. 13 Maintenance........................................................................... pg. 14 Code of Ethics ........................................................................ pg. 14 Specifications......................................................................... pg. 15 ABOUT YOUR FISHER 1270 The 1270 is a “motion” detector and was designed to offer you more versatility in a wide range of conditions: Highly mineralized soil, extremely trashy areas, and deep targets. By utilizing the various controls on the 1270, you will find more items that were unreachable until today. We at Fisher Research Laboratory always strive to give you maximum performance and quality, and have been doing so since 1931. FEATURES: • 3 Search Modes normal discrimination, enhanced iron discrimination, and all metal ground balanced search. • Patented Double Derivative, Crystal Locked Circuitry (U.S. Patent # 4,514,692) • Enhanced Relic Sensitivity • Excellent “see through” in iron trash. • “Cutting Edge” performance in moist soils • Sensitivity Control to enable silent search or • Audio threshold • Silencer for silent (3rd Derivative) discrimination • Trigger Switch mode change • Trigger Switch Zero-Motion Pinpointing • Near Perfect Balance for comfortable use • Lightweight Cushioned Arm Rest & Grip • Low Battery Alert - LED blinks automatically • Drop-in Batteries • Double Locking lower stem • 3 piece breakdown handle • Limited Lifetime Warranty* *may vary outside of the United States. See your dealer for details. (Square) 1 CONDENSED OPERATING INSTRUCTIONS We recommend that you first read this entire operating manual before taking your new 1270 out for a test drive. You’ll be more successful, and have a better chance of finding more treasure. But, we also understand the excitement of the “hunt”, so here are some simple instructions for setting up the 1270. Set the controls as follows: NORMAL DISC = 5 (iron & foil discrimination) SILENCER switch = ON IRON DISC switch = OFF ALL METAL GROUND ADJ. = 0, OFF (completely counter clockwise) SENSITIVITY = 8 Turn the 1270 ON with the ON /OFF Volume control. (adjust volume to a comfortable level) Take your 1270 outside. There’s normally too much metal inside to per form a proper test. Hold the 1270 as shown in Figure 1, and slowly sweep the search coil left and right while moving forward slightly with each sweep. A slight motion is required for the 1270 to detect a target. It is often helpful to bury a few known targets in the soil to get a “feel” for how the 1270 responds to different targets at various sweep rates. Re member, at a DISC setting of 5, certain targets such as iron or aluminum should be ignored. When the 1270 “beeps”, you’ve passed over a metal target with the search coil. Swing the 1270 left and right, then forward and back, making an “X” over the “beep” area. The target will be directly below the center of the search coil. Because the 1270 is a “motion” detector, with practice, this may be the only mode of pinpointing you will need. To use the no-motion pinpoint mode, place the coil on the ground away from the target, pull and hold the MODE TOGGLE SWITCH (on the bot tom of the housing). This switches the 1270 into ALL METAL no motion PINPOINT mode. Keeping the search coil level with the ground, and mov ing the coil near the target you will hear an audio increase. Next, move the 1270 in an “X” pattern over the target and stop where the loudest tone is heard. This will be the center of your target, directly under the center of the search coil. Read this instruction manual thoroughly, practice often and you are in for some exciting treasure hunting. Drop us a line if you have any questions, comments or good finds to tell us about. In the meantime... HAPPY HUNTING! Figure #1 Figure #1 SETTING UP Your new 1270 comes ready to assemble and use, but first review the steps below before proceeding. STEP 1. Unpack your 1270 carefully, and save the carton: It may come in handy on the rare occasion that you may need service. STEP 2. The coil is attached to the lower stem. Depress the spring lock bu...