Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
3 4 EN Microwave oven Installation Requirements Requirements The requirements for proper microwave oven operation are as follows: • Operating Voltage: 24V DC. • Breaking Voltage: Min. 21.5V, Max. 30.2V. • Battery life must be at least 45Ah at 24V . If possible, connect the oven to a separate supply battery (a secondary battery). Supplied Items Microwave oven, Turntable, Terminal Post Cover (plastic cover), Install bracket(Left/Right), 6-#5 Tap screws, 7-#4 screws and Owner’s Manual. The battery connection power cable is not included. Items needed for Installation Before installing the appliance, make sure you have the following items: • 6-#5 Tap screws (The length of the screw is subject to the installation requirements.) • 7-#4 Tap screws (Outer panel screws). • 2 connection power cables : one red, one black(refer to the page 6 for the length and size of the connection cables) • Power cable terminal, power cable binder, and electrical tape. • Depending on the installation location, the following tools may be required. • Stick ruler, chalk, hammer, and gimlet. • Drill and borer. • Ring/Fork type spanner set. • Crimp pincers, soldering iron. • Screw driver. Installation Installation Location Tips • Before installing the oven, be sure to comply with the following: The installation location for the oven should be even, flat, and sturdy. • Do not allow humidity or heat to affect the oven. • Allow free space of about 50mm around the oven for ventilation (Fig.1). • Take the oven’s weight into account. Check whether any protective measure such as a large support base is necessary or not. • To determine hole location, refer to the dimensions in Fig. 2 and follow the instructions. WARNING When installing the oven in a vehicle, make sure that the installation location is safe enough to avoid an injury. (including a vehicle’s sudden stop or accident). To make a hole in an accurate location, create a mark in advance with a hammer and punch. Smooth any rough edges on the holes and apply rust proof treatment to them. • Remove one screw securing outer panel of microwave oven (Right side). • Attach left and right brackets to the outer panel using 8 screws(Fig.1). • Secure the microwave oven brackets to the frame which has drilled holes(O 4.0~4.2) using 6 screws (Tap Screws).(Fig.2). • Fig.3 shows how the microwave should look attached to the frame. If the electrical wiring does not work after the oven is fastened tightly, first follow the “Electrical Wiring (Page 5-6)” instructions and then re-fasten the oven. The oven must be fastened tightly to protect against vibration. If do not want to use brackets, please attach 8 screws (#4x12) on left and right side of the outer panel directly.(Fig.4) Microwave Oven (Fig. 1) Front of Microwave Oven (Fig. 2) Mi cr o w av e o v en I n s t al lation Requirements (continued) EN Safety Requirements for Installation: The operating voltage should comply with the voltage specified in the label of the microwave oven type attached to the back of the appliance. WARNING This appliance is equipped with a capacitor. To remove or relocate the appliance, take the battery out and wait for about 20 seconds, and then disconnect the power cable connections. If the power cable is disconnected too soon, it may cause an electrical short circuit and discharge ( spark). The operating voltage should comply with the voltage specified in the microwave oven type label on the back of the appliance. It is a good idea to install an additional safety fuse to a positive( + ) power cable. If the connection power cable is damaged or causes a short circuit, it means that the safety fuse can no longer prevent the appliance from being damaged ( cable fire) . The safety fuse should be installed as close to the battery as possible. If the electrical cabling is not performed properly, it may cause an electrical short circuit, resulting in the following: • Power cable may catch fire. • Airbag may burst. • Controller may work improperly. • An electrical component may malfunction. (Signal lamp, Brake lamp, Horn, Ignition, Lighting, etc.). To eliminate the danger of an electrical short circuit, always disconnect and isolate the battery negative terminal before using an electrical device in the vehicle. Also, in the case of a vehicle equipped with an additional battery, disconnect and isolate the negative(-) battery power cable. Precaution When disconnecting and isolating the negative battery power cable, all the data stored in the memory of the vehicle's system will disappear. Depending on equipment included in your vehicle, you may have to enter the following data again: Ex) Vehicle audio password, vehicle clock, seat location, panel computer, and time switch. Electrical Wiring Connection Power Cable • Do not pull the power cable forcibly. • Do not connect to a power supply other than 24V. • Comply with the minimum diameter of the power cable as specified in the manual. • Fasten the power cable properly. • Install the power c...