Assessments - 5, GPA: 4
(
)
)
|
Facilidade de uso
3). Clutch Oil Level Gauge Gear Shift Lever Timer Keys Programming Function (if the mixer is not mixing). P1 Contains up to four preset times. Displays each preset time sequentially. P2 Contains up to four additional preset times. Displays each preset time sequentially. Knob Changes the time as indicated by the display. Save Replaces the preset time with the indicated time. Clear Returns to Idle from a programming function. For Continuous Mixing START and STOP buttons control mixing operation. Beginning from the Idle display [ - - : - - ], press START to begin mixing. The M/C indicator will be lit and the total mixing time will be indicated (minutes and seconds). Press STOP when mixing is done; the M/C indicator light goes off; and the Idle display [--:--] returns. Using the Dial Timer to Set the Mixing Time Beginning from the Idle display [ - - : - - ], turn the KNOB to set the mixing time. The M/C indicator will be lit. START and STOP buttons control mixing operation. Press START to begin mixing. The timer will count down from the set time to [ 00 : 00 ]. If STOP is pressed, both mixing and timer countdown will be interrupted. After pressing STOP, press START to resume both mixing and timer countdown, or press CLEAR to return to the Idle display. When the timer reaches [ 00 : 00 ], the mixer stops; the M/C indicator goes off, a beep tone sounds for two seconds, and the Idle display [ - - : - - ] returns. Fig. 3 - 7 - PROGRAMMABLE TIMER CONTROLLER (when equipped) continued Using the Preset Keys, P1 or P2, to Set the Mixing Time Each preset key has four time settings. The indicator above the number 1, 2, 3 or 4 and the P1 or P2 indicator light identify which preset time is being displayed. The chart below shows the default settings; the next page shows how to revise these preset times. The Dial Timer KNOB can be used to adjust the mixing time if the knob is turned prior to pressing START. pi P2 1 2 3 4 Indicators above P1 and 1 indicate the first preset time contained in P1. Beginning from the Idle display [ - - : - - ], press P1 or P2 to display the #1 preset mixing time. (Pressing P1 or P2 again will display the next preset time, etc.) ^ The Dial Timer KNOB can adjust the time. START and STOP buttons control mixing operation. Press START to begin mixing. The timer will count down from the set time to [ 00:00]. If STOP is pressed, both mixing and timer countdown will be interrupted. After pressing STOP, press START to resume both mixing and timer countdown, or press CLEAR to return to the Idle display. When the mixer is stopped, you may perform any appropriate task, such as the following: Add ingredients, change speed, reset the timer, continue mixing or unload. When the timer reaches [ 00 : 00 ], the mixer stops; a beep tone sounds for two seconds, and the next preset mixing time displays. When the last preset time reaches [ 00 : 00 ], the P1 or P2 indicator goes off and the Idle display [ - - : - - ] returns. Repeat from & to complete four preset times. The timer reverts to the Factory Programmed Preset Times after any power interruption: Factory Programmed Preset Times - 8 - PROGRAMMABLE TIMER CONTROLLER (when equipped) continued To Revise the Preset Mixing Times Contained in P1 or P2 Each preset key has four preset time settings. The indicator above the number 1, 2, 3 or 4 and the P1 or P2 indicator light identify which preset time is being displayed. Beginning from the Idle display [ - - : - - ], press P1 or P2 to display the #1 preset mixing time. (Pressing P1 or P2 again will display the next preset time, etc.) P2 01:00 p---i 1 2 3 4 Indicators above P1 and 1 indicate the first preset time contained in P1. ^ Turn the KNOB to change the time for the indicated preset. • Press SAVE to retain the revised time and move to the next preset time. Repeat from ^ for each preset time (1, 2, 3 and 4 contained in P1 or P2). Pressing CLEAR will retain the saved times and return to the Idle display [ - - : - -]. The timer reverts to the Factory Programmed Preset Times after any power interruption: Factory Programmed Preset Times - 9 - CHANGING SPEEDS The Clutch Lever is used when changing speeds. Moving the Clutch Lever to STOP disengages the clutch and activates a brake which stops the planetary. The motor will continue to run with the Clutch Lever on STOP unless the STOP button is pressed. The Gear Shift Lever is used to change speeds. To change speeds, disengage the clutch by moving the Clutch Lever to STOP. The brake is automatically actuated. When the agitator shaft has stopped, move the Gear Shift Lever to the desired speed. Make sure the Gear Shift Lever lines up with the number on the shifter plate — never position the handle between numbers. Place the Clutch Lever on RUN to continue operation. POWER BOWL LIFT CAUTION: Before lowering the bowl onto a bowl truck, always unlock both bowl clamps. The Power Bowl Lift Lever is used to raise or lower the b...
Este manual também é adequado para os modelos :Misturadores - V1401 (800.17 kb)