Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
B (May 2007) Installation, Operation and Care of Model HCM450 Cutter Mixer SAVE THESE INSTRUCTIONS GENERAL The HCM450 Cutter Mixer cuts, mixes or blends foods quickly and efficiently. A transparent lid allows the operator to inspect the product during the mix-cut-blend process. The unit operates continuously, momentarily or with a timer control which shutsoff the machine automatically after the set time has elapsed. The HCM450 bowl has a liquid capacity of 45 quarts. The motor on HCM450 is rated 5 HP, 1140 RPM and has thermal overload protection. The motor is totally enclosed with external fan cooling. The cut mix shaft assembly is used for cutting meat products, vegetables, cheese, pastry, cake products and some doughs that require both cutting and mixing. The knead mix shaft assembly is used for applications where cutting is not required. It is especially good for kneading yeast doughs. The strainer basket may be used when cutting vegetables in water. After cutting, the strainer basket is raised to allow the water to drain away from the food. The bowl is locked in its vertical position during processing with the lock arm on HOLD. After processing, when you move the lock arm from HOLD to TILT, the bowl can pivot to allow easy pouring. When cutting certain products, a hand-operated mixing baffle may be used to stir or move the product into the knives. The mixing baffle may be removed when it is not needed. © HOBART CORPORATION, 1980, 1987, 2002 – 2 – UNPACKING UNPACKING Prior to installation, verify that the electrical service agrees with the specifications on the machine data plate located on the frame behind the control box. ASSEMBLY Remove the cutter mixer from the skid and install rubber feet as follows: Apply a bead of silicon sealant (not provided) around the edge of each leg. Insert a rubber foot onto each leg and fasten with bolts and washers provided. Match the shape of the foot to conform to the shape of the leg. Two of each style are included. NOTE: Optional right and left casters (with rubber caster pads) are available for installation on the two legs on the control panel side. Assemble with the bolts and washers provided for the rubber feet. Place cutter mixer in the desired location. ELECTRICAL CONNECTIONS WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING: DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH, INDICATING THAT THE CIRCUIT IS BEING WORKED ON. Machines are shipped from the factory with a 6-foot cord and plug. A mating receptacle is furnished with the machine as standard equipment. ELECTRICAL DATA Model V/Hz/Ph Minimum Circuit Ampacity Maximum Circuit Breaker Size AMPS HCM450 200/60/3 30 230/60/3 30 460/60/3 20 Check Motor Rotation Check bowl to make sure it is empty, and remove the cut mix shaft assembly or the knead mix shaft assembly. Close and latch the lid. Connect the power cord to its receptacle. Set the timer on JOG. Press START and then release. The motor should rotate in a clockwise direction as indicated by the arrow (Fig. 1). If the motor rotation is incorrect, unplug the power cord, disassemble the plug and interchange any two of the power leads (red, white or black). Do not change the green ground wire. Then reassemble the plug and recheck. Fig. I – 3 – ASSEMBLING BOWL SEAL AND ATTACHMENTS ASSEMBLING BOWL SEAL AND ATTACHMENTS WARNING: BEFORE INSTALLING BOWL SEAL AND ATTACHMENTS, BE SURE THE POWER CORD IS UNPLUGGED. Bowl Seal: Insert the black seal ring in the groove of the white seal retainer so the thin black edge is down and the tapered white part on the retainer is up (Fig. 2). Then install the seal onto the motor shaft with the thin black edge down (Fig. 3). Seat seal securely against the bottom of the bowl with a 1/4 turn. Store the extra seal shipped with the machine in a location where you can find it, if necessary. Fig. 2 Fig. 3 Strainer Basket: If needed, insert basket in bowl over the motor shaft. NOTE: Never use strainer basket and mixing baffl e at the same time. Cut Mix Shaft Assembly or Knead Mix Shaft Assembly: Place on motor shaft, seat square drive at base and tighten hand knob by turning counterclockwise. Lid Scraper: Insert on bar opposite mixing baffle. Lid scraper is used to clean the inside of the bowl cover. Mixing Baffle: Insert shaft of mixing baffle into hole in the center of the lid. With baffle paddle down, hold baffl e handle at an angle so lock handle hangs down and insert onto shaft. Then tighten lock handle (Fig. 4). Fig. 4 – 4 – OPERATION Move bowl tilt handle to HOLD to lock bowl in vertical position (Fig. 5). Close and latch the lid by grasping the lid handle with the left hand. Press lid handle down while turning the latch until lid lock is engaged (Fig. 5). CONTROLS (FIG. 5) The Timer has three mode settings: Run, Jog or Timer. RUN – Machine runs continuously after START is pushed until STOP is presse...