Assessments - 4, GPA: 4.5
(
)
)
|
Facilidade de uso
Never use coarse or caustic cleaning products to clean this appliance. Never immerse the power unit in water. Blender with Unbreakable Plastic Jar (MUZ 4 MX2) WARNING 1. There is a risk of injury from sharp blades when using the blender attachment. 2. Keep hands and utensils out of the blender jar while it is attached to the power unit. 3. Blades are sharp. Handle carefully. 4. To avoid injury, never place blade assembly on power unit without blender jar properly attached. 5. Always operate the blender with the cover in place. Always hold the cover in place when in operation to prevent the cover from being knocked off. 6. The use of attachments, including canning jars, not recommended by the manufacturer, may cause a risk of personal injury. 7. When blending hot and/or frothing liquids, process a maximum of 18 fluid ounces (0.5 litres) at a time. The MUM 4635 UC, MUM 4620 UC and the MUM 4420 UC Bosch Compact Series Kitchen Machines include the MUZ 4 MX2 blender accessory. The blender accessory consists of, figure 5: How to Use Blender The blender has been designed for crushing ice; mixing liquids; pureeing vegetables; preparing special diet and infant foods; pulverizing fruit, vegetables, nuts and dried bread (for bread crumbs); and preparing mayonnaise and sauces. Use of blender Before beginning to use the blender attachment, make sure that the power unit is on a clean, smooth, suitable work surface and switched to off position, “O/Off,” and that you have removed the drive cover from the high-speed drive where the blender will be placed. Figure 5. 5a. Cover closure/funnel 5b. Cover 5c. Blender jar 5d. Blade/base assembly with gasket and locking ring. 1. Before using the blender for the first time, it is recommended that the blender jar cover, closure/funnel and blade/base assembly, gasket and locking ring be washed. All components, except the blade/base assembly, are dishwasher safe. Remove the blade/base assembly from the blender: First remove the locking ring, as shown in figure 6a and 6b. Then turn the blender over so that the base is facing upward, as shown in figure 7, and remove the blade assembly by turning 13 the blade assembly counterclockwise until it stops and then lift up see figures 7c and 7e. Figure 6. CAUTION Blade/base assembly is very sharp. Handle with care. Figure 7. If the blade assembly is too tight to turn by hand, the locking ring may be used to loosen the blade assembly, as shown in figure 7d. After loosening, turn the blade assembly counterclockwise until it stops and then lift up. The gasket may be removed for cleaning, as shown in figure 7f. Wash the blade/base assembly under running water. Do not place the blade/ base assembly in the dishwasher or allow it to stand in water. This will tend to wash out the lubricant. After cleaning, rinse thoroughly and dry before using. 2. To assemble or reassemble blade/base assembly into the blender, reverse the steps that were used in the above to remove it. 3. The blender is used in mode 3, see table 1. To place the blender on the power unit the arm must be rotated to the down position. Depress the release button, see 4a, and lower the arm so that the arm is vertical and the high- speed drive is straight up. If you have not already done so, remove the motor drive cover from the high-speed drive and place the blender on the high-speed drive and turn counterclockwise to lock the blender in place. Placing Blender into Operation Make sure that the power unit’s rotary switch is in the off position, “O/Off.” Pull the electrical cord or unwind it to the necessary length and then plug into the wall outlet. The blender is now ready for operation. Normally when blending, the blender jar should be filled with the entire amount of material to be blended, if possible, before switching the appliance to On. The cover and cover closure should always be in place after filling the blender jar and before switching the power unit to On. Any subsequent additions to the blended material should be made through the cover opening, see figure 8. For solids and/or granular material, remove the cover closure/ funnel to add the material, as shown in figure 8a. For liquids, the closure/funnel may be left in place and the liquids can be added by pouring them into the closure/ funnel, see figure 8b. 14 Figure 8. Example of Use of Blender To familiarize you with the operation of the blender, a sample recipe for mayonnaise is provided below: Mayonnaise Recipe 1 whole egg 1/3 cup of vegetable oil 2 tablespoons lemon juice or light vinegar 1 teaspoon sugar 1/2 teaspoon dry mustard 1/2 teaspoon of salt 2/3 cup of vegetable oil Mix all ingredients, except final 2/3’s cup of oil, for a few seconds at speed 1, then quickly pour the oil in through the opening in the cover in a uniformly thick stream, as shown in figure 8b. Operate the blender at speeds 1 or 4 until mixture is thick and smooth (approximately 10–20 seconds). Makes 1 1/4 cups. Tips: The blender should be operated with...
Este manual também é adequado para os modelos :Misturadores - MUZ 4 MX2 (1.32 mb)