Assessments - 1, GPA: 5
(
)
)
|
Facilidade de uso
HIGH PRESSURE SPRAY CAN CAUSE SERIOUS INJURY. FOR PROFESSIONALUSE ONLY. OBSERVE ALL WARNINGS. Read and understand all instruction manuals before operating equipment. FLUID INJECTION HAZARD General Safety Pressure Relief Procedure This pressure washer generates very high fluid To reduce the risk of serious bodily injury, including fluid pressure. Spray from the gun, leaks or ruptured injection and splashing in the eyes oron the skin, components can inject fluid through your skin and into always follow this procedure whenever you stop your body and cause extremely serious bodily injury spraying for more than 10minutes, when shuttingdown, including the need for amputation. Also, fluid injected orand before checkingor repairing any partof the system. splashed into the eyes or on the skin can cause serious damage. 1. Engage the trigger safety latch. NNER point the spray gun or wand at anyone or at any2. Tum the sprayer off. part of the body. NNER put hand or fingers over the spray tip. ALWAYS follow the Pressure Relief Procedure, before cleaning or servicing any part of the sprayer. NNER try to stop or deflect leaks with your hand or body. Be sure equipment safety devices are operatingproperly before each use. Medical Treatment If any fluid appears to penetrate your skin, get EMERGENCY MEDICALTREATMENTATONCE. DO NOT TREATAS A SIMPLE CUT. Tell the doctor exactlywhat fluid was injected. NOTE TO PHYSICIAN Injectionin the skinis a traumatic injuty ItIs lmpotiantto treat the Injury surglcally .as soon as possible. Do not delay treatment to research tawiciiy. Toxicity is a concern' with some exotic coatings injected direct@inMthe bloodstream. Consultationwith a p/astic surgeon or reconstructiVe handsurgeon may be adrisable. 3. Remove the ignition cable from the spark plug. 4. Shut off the water supply. 5. Disengage the trigger safetylatch and trigger the gun to relieve pressure, and then engage the triggersafety latch again. 6. Before long-term (overnight) storage or transporting of unit, disconnect the water supplyand turn off the fuel supply valve. Spray Gun Safety Devices Be sure all gun safety devices are operating properlybefore each use.Do not remove or modify any partof the gun; this can cause a malfunction and result in serious bodily injury. SAFEPl LATCH: Whenever you stop spraying for a moment, always set the gun safety latch in the engagedor "safe" position, making the gun inoperative. Failure to properly set the safety latch can result in accidental trlggering of the gun. SPRAY TIP SAFETY: Use extreme caution when cleaning or changing spray tips. If a spray tip clogs while spraying, engage the gun safety latch immediately. ALWAYS follow the Pressure Relief Procedure and then remove the spraytip to clean it. 2 308-531 FUEL AND EMISSION HAZARDS NEVER flllthe fuel tank while the unitis wnning or hot. NEVER alter the throttle settlng, whichIs factory set. The fuel used in this unit is combustible and when Tampering with this adjustment can damage the spilled on a hot surface can ignite and cause a fire. pressure washer and will void the warranty. ALWAYS filltank slowly to avoid spilling. NNER operate the' unit in a closed building. The exhaust contains carbon monoxide, a poisonous, odorless, invisible gas which can cause serious injury or deathif inhaled. EQUIPMENT MISUSE HAZARD General Safety Any misuse of the pressure washer or accessories,such as overpressurizing, modifying parts, usingincompatible chemicals and fluids, or using worn or damaged parts, can cause them to rupture andInresult fluid injection, splashing in the eyes or on the skin, or other serious bodiiy injury, fire, explosionor properly damage. NEVER alter or modify any part of this equipment; doing so could cause it to malfunction. CHECK all spray equipment regularly and repair or replace wom or damaged parts immediately. ALWAYS wear protecthre eyewear and appropriateclothing. If using a chemicai injector, read and follow the chemical manufacturer's literature for recommendations on additional protective equipment, such as a respirator. HOSE SAFETY High pressure fluid be very dangerous. in the hoses can If the hose developsa leak, split or rupture due to any entire hose for cuts, leaks, abrasion, bulging cover, or kind of wear, damage or misuse, the high pressure damage or movement of the hose couplings. If any of spray emitted fromitcan cause a fluid injection injun/ or these conditions exist, replace the hose immediately: other serious bodily injury or property damage. ALL FLUID HOSES MUST HAVE STRAlN RELIEFS ON BOTH ENDS. The strain reliefs help protect the hose from kinks or bends at or close to the coupling, which can result in hose rupture. T/GM€N all fluid connections securely before each use. High pressure fluid can dislodge a loose couplingor allow high pressure spray to be emitted from the coupling. MOVING PARTS HAZARD Moving parts can pinch or amputate fingers or other body parts. KEEP CLEAR of moving parts when starting or operati...