Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
Use PTFE liquid or tape. Pressure gauge inoperative or not registering accurately. Check pressure with new gauge and replace as needed. Relief valve stuck partially plugged or improperly adjusted. Clean and reset relief valve to system pressure and correct bypass. Check supply tank for contamination. Worn seat or valves. Clean or replace with valve kit. Inlet suction strainer clogged or improperly sized. Use adequate size for inlet pump connection and fluid being pumped. Clean frequently. Worn seals. Abrasives in pumped fluid, severe cavitation; inadequate water supply, stressful inlet conditions. Install and maintain proper filter, check line size and flow available to pump. Install a C.A.T. Fouled or dirty inlet or discharge valves. Clean inlet and discharge valve assemblies. Worn inlet or discharge valves. Replace with valve kit. Leaky discharge hose. Replace hose. Check connections. Pulsation, pump runs extremely rough, pressure low. Faulty Pulsation Dampener Check precharge (should be 30-50%) of system pressure or replace as needed. Restricted inlet or air entering inlet plumbing. Check filters and clean as needed. Check fittings and use PTFE liquid or tape for air tight connection. Stuck inlet or discharge valve Clean or replace valve. Check supply tank for contamination. Water leakage from under the manifold Worn seals Replace with seal kit, check inlet pressure and system temperature, use Thermo Valve in by- inlet pressure regulator in inlet line. Oil leak between crankcase and pumping section *Slight leakage. Worn crankcase seals Replace crankcase seals Oil leaking in area of crankshaft Worn crankshaft seal Bad bearing Replace damaged seals. Replace bearing. Excessive play in the end of the crankshaft. Worn bearing Replace bearing. Water in crankcase inside of the crankcase Humid air condensing into water Change oil every 3 months or 500 hours intervals using premium grade 10W30 Non-detergent hydraulic oil, (other approved oil every month or 200 hours.) Leaking of crankcase seals or seals installed backward Replace seals. Follow proper installation procedure. Contact Cat Pumps supplier for crankcase servicing. Oil leaking at the rear portion of the crankcase Damaged or improperly installed oil gauge, crankcase cover, or drain plug o-ring Replace oil gauge, crankcase cover or drain plug o-ring. Thread in oil gauge and drain plug hand tight to avoid extruding o-ring. Loud knocking noise in pump Pulley loose on crankshaft Check key and tighten screw Worn bearing, connecting rod or crankshaft. Consult Cat Pumps supplier for crankcase servicing. Stressful inlet conditions. Install C.A.T. Frequent or premature failure of the packing Cracked or scored plungers Abrasive material in the fluid being pumped Check supply tank for contamination. Replace plungers Install proper filtration on pump inlet plumbing. Excessive pressure and/or temperature of fluid being pumped. Check pressure and fluid inlet temperature; be sure they are within specified range. Over pressure of inlet or discharge Reduce pressure per specifications. Running pump dry. DO NOT RUN PUMP WITHOUT WATER! Strong surging at the inlet and low pressure at the discharge side. Foreign particles in the inlet or discharge valve or worn inlet or discharge valves. Check for smooth surfaces on inlet and discharge valve seats. Replace with kit if pitted or worn. Check supply tank for contamination, Install and regularly clean filter. Do not pump abrasive fluids. Manual Page 12 Notes: Manual Page 13 Repair Kits Pos Code Description Qty. 44 67 40 69 41 42 70 2 1 3 4 5 4 3 1 2 6 7 8 9 12 13 11 10 14 15 16 17 20 19 18 21 22 23 24 25 27 33 28 27 36 35 34 37 38 28 32 31 30 27 28 71 72 73 74 57 3(6) 4(6) 6(3) 16 30(3) 42 7(3) 10 32(3) 33(3) 25(3) 24(3) 23(3) 22(3) 21(3) Valve Kit # PPA1554 Qty 6 of each part included per kit Piston Kit # PPA1555 Qty 3 of each part included per kit Water Seal Kit #PPA 1556 Qty 3 of each part included per kit Support Ring Kit #PPA 1558 Qty 3 of each part Oil Seal Kit #PPA 1557 included per kit Includes 3 of part #30 PUM0015 1 PPA1501 O-Ring 6 2 PPA1502 TBD 6 3 PPA1504 ValveAssembly 6 4 PPA1505 O-Ring 6 5 PPA1506 Plug 1 6 PPA1507 SupportRing15 3 7 PPA1508 Gasket15mm 3 8 PPA1509 PistonGuide15mm 3 9 PPA1510 PumpBody 1 10 PPA1511 BearingCap 1 11 PPA1512 Circlip52mm 1 12 PPA1513 SnapRing 1 13 PPA1514 Bearing 1 14 PPA1515 OilCap/Dipstick 1 15 PPA1516 PistonPin 3 16 PPA1517 Gasket 1 17 PPA1518 Screw 6 18 PPA1519 CrankcaseCover 1 19 PPA1520 ConnectingRod 3 20 PPA1521 GuidingPiston 3 21 PPA1522 O-Ring 3 22 PPA1523 Washer 3 23 PPA1524 Piston15mmXm 3 24 PPA1525 Washer 3 25 PPA1526 Nut 3 27 PPA1527 O-Ring 3 28 PPA1528 Plug 3 29 PPA1529 Screw 4 30 PPA1530 OilSeal 3 31 PPA1531 PistonGuide15mm 3 32 PPA1532 O-Ring 3 33 PPA1533 Gasket15mm 3 34 PPA1534 Plug:1/2” 1 35 PPA1535 O-Ring 1 36 PPA1536 PumpHeadBrass 1 37 PPA1537 Lockwasher 8 38 PPA1538 Screw 8 40 PPA1539 Bearing 1 41 PPA1540 SnapRing 1 42 PPA1541 OilSeal 1 44 PPA1542 Screw8X20 4 53 PPA154...
Este manual também é adequado para os modelos :Equipamento de lavagem - KING BRUTE PN 09301 A (1.95 mb)
Equipamento de lavagem - KING BRUTE PN 09301 A (1.95 mb)