Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
Make sure fuel shut off valve is open and throttle is in the Rabbit position. NOTE: If any leaks are present shut unit down and tighten fittings. 10 How To Use Your Pressure Washer On the end of your spray gun wand is a quick connect body. Mounted to your pressure washer handle are five quick connect nozzies. To achieve desired spray pattern, insert one of the five quick connect nozzies. Start by puliing the quick connect sleeve back and then insert the desired nozzle tip. Then press down on the nozzle tip to insure that it is in the locked position and ready to use. IMPORTANT: When switching out tips, be sure the gun trigger is in the locked position and engine is turned off. Each nozzle tip will give you a varying degree of spray patterns. • Black - Soap nozzle; used when wanting to draw chemical • White - 40° spray pattern • Green - 25° spray pattern • Yellow - 15° spray pattern • Red - 0° spray pattern IMPORTANT: If you get spray nozzle too close, especially on high pressure, you may damage the cleaning surface. • The pressure control knob is located on the pump. You can increase the pressure by turning the knob clockwise or decrease the pressure by turning the knob counterclockwise. PRESSURE CONTROL KNOB NOTE: The unit is set at its maximum pressure at the factory. Do not attempt to adjust the pressure higher than this factory setting. Prepare the soap/chemical as required by your job. Insert soap/chemical line into your container (soap/ chemicals not included). NOTE: The first step involves applying an appropriate soap/chemical solution to penetrate and loosen grime. The soap/chemical is applied at low pressure to avoid splashing, over spray and waste. Leave the solution on surface for 3 to 5 minutes to aliow solution to work. NOTE: The second step involves cleaning the surface you have prepared with the pressure washer and then rinsing it clean. * Turn the adjustable nozzle counter clockwise to low pressure mode. Soap/chemicals cannot be applied with nozzle in high pressure position. * Review the use of the adjustable nozzle. • Connect garden hose to water inlet (see "To Start Your Pressure Washer"), check that high pressure hose is connected to spray gun and pump (see Assembly), and start engine. • Apply soap/chemicals to dry surface, starting from the bottom and working up. * Aliow the soap/chemicals to soak in between 3-5 minutes before washing and rinsing. • For cleaning, start at lower portion of area to be washed and work upward, using long, even overlapping strokes. Your pressure washer is equipped with a chemical injector adjustment knob. With the knob fully opened you will get maximum chemical draw. With knob fully closed you will get no chemical draw. Turn knob in counter clockwise direction to achieve more chemical draw and clockwise for less chemical draw. Using Soaps/Chemicals IMPORTANT: Use soaps and chemicals that are designed specifically for use with pressure washers. To apply soap/chemicals follow these steps: • After using the pressure washer, it is recommended the pump, chemical injector and chemical line be flushed with clear water. To do so, simply place chemical injector hose in water and siphon for 1 to 2 minutes. 11 MAINTENANCE CUSTOMER RESPONSIBILITIES TABLE MAINTENANCE TASK Before each use Every 25 hours oryearly fcvery 50 hours oryearfy Every 100 hours or yearly PRESSURE WASHER Check/clean inlet screen. X Check high pressure hose. X Check soap and chemical hose and filter X Check gun and wand forieaks. X Purge pump ofairand contaminants X Change pump oii X X ENGINE Check oil level X Change engine oii X Clean air cleanerand precieaner X Clean engine muffler & finger guard X Clean/replace spark plug X Product Specifications Pressure Washer Specifications Pressure 2600 Flow Rate 2.7 GPM Cleaning Units (psi x GPM) 7020 Engine Specifications RPM 3600 Rated Horsepower 6.5 Spark Plug Gap 0.030” (0.76mm) Gasoline Capacity 3 Quarts Oil SAE 30 weight Genera! Recommendations The warranty of the high pressure washer does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain high pressure washer as instructed in this manual. Some adjustments will need to be made period-ocally to maintain your high pressure washer. Once a year you should clean or replace the spark plug and clean or replace the air filter and check the gun and wand assembly for wear. A clean spark plug and clean air filter assure proper fuel-air mixture and heip your engine run better and last longer. NOTE: Over time the o-rings in the gun assembly become worn. Attached to your owners manual is a repiacememt o-ring and split backup ring. 12 Pressure Washer Maintenance Check and Clean Inlet Screen: Examine inlet screen on pump iniet fitting. Ciean if clogged replace if torn. ' Check High Pressure Hose: High pressure hose can...
Este manual também é adequado para os modelos :Equipamento de lavagem - 919.769020 (1.16 mb)