Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
The high pressure setting is for cleaning and rinsing, the low pressure setting is for applying chemicals or cleaning solutions to surfaces. Risk of injection or injury to person. Do not direct discharge stream toward persons, unprotected skin, eyes, or towards any pets or animals. Serious injury can occur. For high pressure operation, pull back the nozzle of the multi-reg wand as shown. 11- ENGD25852 The nozzle at the end of the multi-reg wand can be rotated to change the high pressure spray pattern from a narrow jet to a 40. fan shape, as shown. Markings have been placed on the nozzle to help you select the spray pattern. 40. fan spray narrow jet stream For low pressure operation, extend the nozzle of the multi-reg wand as shown. TO SIPHON CHEMICALS/CLEANING SOLVENTS Siphoning chemicals or cleaning solvents is a low pressure operation. NOTE: Use only soaps and chemicals designed for pressure washer use. Do not use bleach. 1. Press chemical hose onto barbed fitting located near high pressure hose connection of pump as shown. Barb fitting D2585212- ENG 2. Place other end of chemical hose with filter on it into container holding chemical/cleaning solution. 3. Set multi-reg nozzle to low pressure setting, see How To Use Wand paragraph in this section. 4. After use of chemical, siphon clean water through chemical hose to rinse it and pump clean. Chemicals which remain in pump can damage it. Damage to pump due to chemicals will not be covered under warranty. NOTE: Chemicals and soap will not siphon when wand is in the high pressure setting. TO SHUT DOWN IMPORTANT: Read and understand how to shut down the pressure washer before operating. 1. If you have siphoned chemicals, siphon a bucket of clean water through the chemical hose. NOTE: Failure to do so will cause damage to the pump. 2. Turn engine off by placing the throttle control in the OFF position. NOTE: NEVER turn the water off with the engine running. 3. Turn the fuel valve to the OFF position if engine will not be restarted soon. 4. Turn water source off. 5. Pull trigger on spray gun to relieve any water pressure in hose or spray gun. 6. See Storage section in this manual for proper storage procedures. BEFORE STARTING Read and understand all Important Safety Instructions in the front of this manual and the following Cautions and Warnings before starting the pressure washer. • Never fill fuel tank completely. Fill tank to 1/2" below bottom of filler neck to provide space for fuel expansion. Wipe any fuel spillage from engine and equipment before starting engine. • Never fill fuel tank indoors. Never fill fuel tank when engine is running or hot. Do not smoke when filling fuel tank. • Never run engine indoors or in enclosed, poorly ventilated areas. Engine exhaust contains carbon monoxide, an odorless and deadly gas. • Never turn water supply off while pressure washer engine is running or damage to pump will result. • DO NOT use hot water, use cold water only. • DO NOT stop spraying water for more than two minutes at a time. 1. Add fresh high quality unleaded gasoline with a pump octane rating of 86 or higher. Do not overfill. Wipe up spilled fuel before starting the engine. 2. Remove filler cap/dipstick and add engine oil (supplied) to engine. NOTE: There will be a slight amount of oil in the engine from factory testing. Always check oil level before each startup. Filler cap/dipstick 3. Verify the filter screen is in water inlet of pump, as shown. Filter Screen 4. Connect high pressure hose to pump outlet. 5. Connect water source to pump inlet. NOTE: Water source must provide a minimum of 5 gallons per minute at 20 p.s.i. Water Source High Pressure Hose 6. If you are applying a chemical or cleaning solution, See How To Siphon Chemicals/Cleaning Solvents in Operation section of this manual. 7. Turn water source on. NOTE: Make sure water supply is turned on. 13- ENG D25852 8. Turn fuel valve to the ON position, 1/4 turn counterclockwise. 9. Move the choke control lever to the CHOKE ON position and the throttle control to the FAST position. NOTE: No choke is Fuel Valve Knob Choke Control Throttle Control needed to start a warm engine. 10. Pull starter grip slowly until you feel resistance, then pull briskly. Return starter grip gently. Pull rope with a rapid full arm stroke. Let rope rewind slowly. Repeat if necessary. If the engine does not start after two pulls, pull the trigger to relieve the pressure. 11. If the choke was used to start the engine, move the choke lever to the OFF position. 12. Depress trigger on gun to start water flow. Release trigger to stop water flow. 13. Adjust nozzle spray for the task being performed. See How To Use Wand instructions in this section. DO NOT let hoses come in contact with very hot engine muffler during or immediately after use of your pressure washer. MAINTENANCE WHEN PERFORMING MAINTENANCE, YOU MAY BE EXPOSED TO HOT SURFACES, WATER PRESSURE, MOVING PARTS, OR FIRE RESULTING IN DEATH. BEFORE PERFORMING ANY MAINTENANCE...
Este manual também é adequado para os modelos :Equipamento de lavagem - 919.769060 (647.56 kb)