Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
See How To Use Wand instructions in this section. SHUTTING DOWN 1. After each use, if you have applied chemicals, place chemical hose into container of clean water and draw clean water through chemical injection system to rinse system thoroughly. Risk of property damage. Failure to do so could cause damage to the pump. 2. Turn engine off. See Engine Owner’s Manual. Risk of property damage. NEVER turn the water off with the engine running. 3. Turn water source off. 4. Pull trigger on spray gun to relieve any water pressure in hose or spray gun. 5. See Storage section in this manual for proper storage procedures. 13 - ENG A16064 MAINTENANCE MAINTENANCE Risk of burn hazard. When performing maintenance, you may be exposed to hot surfaces, water pressure or moving parts that can cause serious injury or death. Risk of fire hazard. Always disconnect, spark plug wire, let the engine cool and release all water pressure before performing any maintenance or repair. The engine contains flammable fuel. Do not smoke or work near open flames while performing maintenance. To ensure efficient operation and longer life of your pressure washer, a routine maintenance schedule should be prepared and followed. If the pressure washer is used in unusual conditions, such as high-temperatures or dusty conditions, more fre quent maintenance checks will be required. ENGINE Consult the Engine Owners Manual for the man u fac turer's recommendations for any and all maintenance. NOTE: The engine drain plug is located at the rear of the unit. PUMP The pump on this unit is maintenance free and requires no oil, if there is a problem with the pump contact an Authorized Service Center. NOZZLE CLEANING If the nozzle becomes clogged with foreign materials, such as dirt, excessive pressure may develop. If the nozzle becomes partially clogged or restricted, the pump pressure will pulsate. Clean the nozzle immediately using the nozzle kit supplied and the following instructions: 1. Shut off the pressure washer and turn off the water supply. 2. Pull trigger on gun handle to relieve any water pressure. 3. Disconnect the spray wand from the gun. 4. Remove the high-pressure nozzle from the spray wand. Remove any obstructions with the nozzle cleaning tool provided and backflush with clean water. 5. Direct water supply into spray wand to backfl ush loosened particles for 30 seconds. 6. Reassemble the nozzle to the wand. 7. Reconnect spray wand to gun and turn on water supply. 8. Start pressure washer and place spray wand into high pressure setting to test. HOW TO CLEAN THE WATER INLET FILTER This screen filter should be checked periodically and cleaned if necessary. 1. Remove fi lter by grasping end and removing it from water inlet of pump Filter Screen as shown. 2. Clean fi lter by flushing it with water on both sides. 3. Re-insert fi lter into water inlet of pump. NOTE: Cone side faces out. NOTE: Do not operate pressure washer without filter properly installed. A16064 14- ENG STORAGE STORAGE ENGINE Consult the Engine Owners Manual for the manufacturer's recommendations for storage. PUMP The manufacturer recommends using a pump protector/winterizer, such as DP80, when storing the unit for more than 30 days and/or when freezing temperatures are expected. If a pump protector/winterizer is not available, RV antifreeze or windshield washer fluid needs to be run through the pump as outlined in the steps below. NOTE: Using a pump protector/ winterizer, RV antifreeze or windshield washer fluid is to provide proper lubrication to the internal seals of the pump regardless of temperature or environment. 1. Obtain a funnel, 6 oz. (170 ml) of RV antifreeze or windshield washer fluid, and 16–36" (40.6– 91.5 cm) of garden hose with a male hose connector attached to one end. Risk of property damage. Use only RV antifreeze. Any other an ti freeze is corrosive and can damage pump. 2. Disconnect spark plug wire. 3. Connect length of garden hose to water inlet of pump. 4. Add RV antifreeze or windshield washer fluid to hose as shown. 5. Pull engine starter rope slowly several times until antifreeze/ washer fluid comes out of high- pressure hose con nec tion of pump. 6. Remove garden hose from water inlet of pump. 7. Reconnect spark plug wire. PRESSURE WASHER 1. Drain all water from high pressure hose, coil it, and store it in cradle of the pressure washer handle. 2. Drain all water from spray gun and wand by holding spray gun in a vertical position with nozzle end pointing down and squeezing trigger. Store in gun holder. 3. Store chemical hose so it is protected from dam age. 4. If space is needed, remove handles and replace as shown. 15 - ENG A16064 TROUBLE SHOOTING GUIDE PROBLEME CAUSE CORRECTION Engine will not start (see Engine Manual for further engine troubleshooting) No fuel. Add Fuel. Pressure builds up after two pulls on the recoil starter or after initial use. Squeeze gun trigger to relieve pres sure. Choke lever in the "No Choke" position. Move choke to the "Ch...
Este manual também é adequado para os modelos :Equipamento de lavagem - A16064 (1.87 mb)