Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Each 100 hours of operation or every 3 months • Clean or replace paper air cleaner cartridge. Tap gently to remove dirt. • Change engine oil. Every 500 hours of operation (5 months) • Change pump oil. Cannot check or change pump oil on the 5525PW. NOTE: This is a general maintenance schedule. Refer to the Engine operation manual for specific information on your engine. 18 — English TECHNICAL AND CONSUMER INFORMATION Pressure Washers Engine Oil Type SAE 10W-30 SAE 30W (Above 60 °F/15.7° C) Engine Oil Capacity 5525PW - Honda GCV160 - 18.6 fl. oz. (0.550 L) 6030PW - Subaru EX17 - 20 fl. oz. (0.591 L) 9030PW - Subaru EX27 - 37 fl. oz. (1.09 L) 1335PW - Honda GX390 - 37 fl. oz. (1.09 L) Engine Fuel Capacity 5525PW - Honda GCV160 - 0.29 gal (1.09 L) 6030PW - Subaru EX17 - 0.95 gal (3.6 L) 9030PW - Subaru EX27 - 1.61 gal (6.1 L) 1335PW - Honda GX390 - 1.72 gal (6.5 L) Pump Oil Type 5525PW - AR Pump - Special. See pump parts list. 6030PW, 9030PW, 1335PW - CAT Pumps Special CAT pump oil. See pump parts list. DO NOT use any oil in pumps other than the manufacturer's oil. Pump Oil Capacity 5525PW - AR RM Pump - 3.5 oz. (0.103 L) 6030PW - CAT 3DX Pump - 8.5 oz. (0.251 L) 9030PW and 1335PW - CAT 66DX Pump - 18 oz. (0.532 L) Pump Detergent Suction Water to detergent 8 to 1 (12% ratio (5525PW) detergent) Water to detergent 10 to 1 (10% ration (6026PW, detergent) 9030PW, 1335PW) Water Supply Requirements Minimum inlet pressure 20 psi Maximum inlet pressure 100 psi Maximum inlet temperature 100° F / 38° C Minimum inlet flow rate Use 5525PW 5 gpm (18.9 lpm) 6026PW, 9030PW, 2 times the rated 1335PW flow of unit or 8 gpm (30.3 lpm) Inlet garden hose size 5/8” ID (15.9 mm) Maximum inlet garden hose length 50 ft. (15,2 m) English — 19 TROUBLESHOOTING CHART Troubleshooting Chart - Gasoline Powered Pressure Washers Only Symptom Possible Cause(s) Corrective Action(s) Engine will not start 1. No gasoline in fuel tank or 1. Fill the tank with gasoline,open fuel or is hard to start carburetor shut off valve. Check fuel line and carburetor 2. Low oil 2. Check oil level. Fill if necessary 3. Start/Stop switch in stop position 3. Move switch to start position 4. Water in gasoline or old fuel 4. Drain fuel tank and carburetor. Use new fuel and dry spark plug 5. Dirty air cleaner filter 5. Remove and clean or replace 6. Spark plug dirty, wrong gap or 6. Clean, adjust the gap, or replace wrong type 7. Spray gun closed 7. Trigger spray gun 8. Other causes 8. See engine owner’s manual Engine misses or 1. Partially plugged air cleaner filter 1. Remove and clean or replace lacks power 2. Spark plug dirty, wrong gap or 2. Clean, adjust the gap, or replace wrong type 3. Drain fuel and carburetor. Use new 3. Bad Fuel fuel. Low pressure and/or 1. Worn or wrong size tip 1. Replace with tip of proper size pump runs rough 2. Inlet filter on pump clogged 2. Clean. Check more frequently 3. Worn water seals, abrasives in 3. Check filter. Replace water seals. See water, or natural wear service center 4. Fouled or dirty inlet or discharge 4. Clean inlet and discharge valve valves assemblies. Check filter 5. Restricted inlet 5. Check garden hose, may be collapsed or kinked. Check inlet water flow 6. Worn inlet or discharge valves 6. Replace worn valves 7. Leaking high pressure hose 7. Replace high pressure hose 8. Pump drawing in air 8. Ensure hoses and fittings are tight 9. Unloader valve seat faulty or worn 9. Check and replace 10. Inlet water temperature too high 10. Check water temperature; may not exceed 100° F / 38° C Water leakage from Worn water seals Install new water seals. See service center under pump manifold Water in pump 1. Humid air condensing inside 1. Change oil as specified in maintenance crankcase (milky oil) crankcase schedule 2. Oil seals leaking 2. Install new oil seals. See service center 3. Water seals leaking 3. Install new water seals. See service center Frequent or premature failure of the pump water seals 1. Scored damaged or worn plungers 2. Abrasive material in the fluid 3. Inlet water temperature too high 4. Overpressurizing pump 5. Excessive pressure due to partially plugged or damaged tip 6. Pump running too long without spraying 7. Pump running dry 1. Install new plungers. See service center 2. Install proper filtration on pump inlet plumbing 3. Check water temperature; may not exceed 100° F / 38° C 4. DO NOT modify any factory set adjustments 5. Clean or replace tip 6. NEVER run pump more than 2 minutes without spraying 7. DO NOT run pump without water Strong surging at Foreign particles in the inlet or Clean or replace valves. See service center the inlet and low discharge valve or worn inlet and/or pressure discharge valves 20 — English TROUBLESHOOTING CHART Symptom Possible Cause(s) Corrective Action(s) Oil leakage Worn oil seals and/or o-ring Replace oil seals and/or o-ring. See service between the engine center and the pump Fluctuating pressure 1. Low engine oil 1. Add oil. 2. Pump valve worn, dirty or stuck 2. Check...
Este manual também é adequado para os modelos :Equipamento de lavagem - 1335PW (3.37 mb)
Equipamento de lavagem - 5525PW (3.37 mb)
Equipamento de lavagem - 6026PW (3.37 mb)