Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
Changing or refilling the oil in the pump requires removal of the pump from the engine and should not be required unless oil has leaked out due to worn or damaged oil seals in the pump. If oil has leaked out of the pump, bring the pressure washer to a certified service center for repair. For models 6027PW, 9032PW, and 1340PW: These units all have a sight glass to check the oil level and have a drain plug to remove the old oil when changing. To add oil remove vent cap from top of pump [See Figure 19 (A)]. Changing oil: Remove the oil drain plug located at the backside of the pump [See Figure 19 (C)]. Drain old oil. Replace drain plug. Refill pump with the correct type and amount of oil (see below for oil types and amounts). Check oil level. Upon starting the pressure washer check for any pump oil leaks. Pump Oil Type 5525PW -Lavor Pump - Special. See pump parts list. 6027PW, 9032PW, 1340PW - CAT Pumps Special CAT pump oil. Use 531 30 74-83. DO NOT use any oil in pumps other than the manufacturer's oil. English — 17 MAINTENANCE SCHEDULE Maintenance Schedule Action needed Each use • Check water inlet screen and filter. • Check engine and pump oil levels. Fill as necessary. Cannot check pump oil on the 5525PW. • Check gasoline level. Fill as necessary. After first 5 hours of operation • Change engine break-in oil. Use SAE30 or 10W-30 detergent oil if below 60° F (15.7° C). After first 50 hours of operation • Change pump oil. Cannot check or change pump oil on the 5525PW. Every 25 hours of operation • Change engine oil if operating under heavy load or high ambient temperature. • Remove and clean foam pre-cleaner or foam air filter (if applicable). Wash with water and mild detergent. Dry thoroughly. Rub with oil and squeeze to distribute oil. Every 50 hours of operation • Change engine oil. • Replace spark plug. Each 100 hours of operation or every 3 months • Clean or replace paper air cleaner cartridge. Tap gently to remove dirt. • Change engine oil. Every 500 hours of operation (5 months) • Change pump oil. Cannot check or change pump oil on the 5525PW. NOTE: This is a general maintenance schedule. Refer to the Engine operation manual for specific information on your engine. 18 — English TECHNICAL AND CONSUMER INFORMATION Pressure Washers Engine Oil Type SAE 10W-30 SAE 30W (Above 60 °F/15.7° C) Engine Oil Capacity 5525PW -Honda GCV160 - 18.6 fl. oz. (0.550 L) 6027PW -Honda GX160 - 20 fl. oz. (0.591 L) 9032PW -Honda GX270 - 37 fl. oz. (1.090 L) 1340PW -Honda GX390 - 37 fl. oz. (1.090 L) Engine Fuel Capacity 5525PW -Honda GCV160 - 1.2 US quarts (1.09 L) 6027PW -Honda GX160 - 3.3 US quarts (3.1 L) 9032PW -Honda GX270 - 5.6 US quarts (5.3 L) 1340PW -Honda GX390 - 6.4 US quarts (6.1 L) Pump Oil Type 5525PW -Lavor Pump -Special. See pump parts list. 6027PW, 9032PW, 1340PW -CAT Pumps -Special CAT pump oil. See pump parts list. DO NOT use any oil in pumps other than the manufacturer's oil. Pump Oil Capacity 5525PW -AR RM Pump -3.5 fl.oz. (0.103 L) 6027PW -CAT 3DNX Pump -8.5 fl.oz. (0.251 L) 9032PW -CAT 66DX Pump -10.15 fl.oz. (0.532 L) 1340PW -CAT 66DX Pump -18 fl.oz. (0.532 L) Pump Detergent Suction Water to detergent 8 to 1 ratio (5525PW) (12% detergent) Water to detergent 10 to 1 ratio (6027PW, 10% detergent) 9032PW, 1340PW) Water Supply Requirements Minimum inlet pressure 20 psi Maximum inlet pressure 100 psi Maximum inlet temperature 100° F / 38° C Minimum inlet flow rate 5525PW 5 gpm (18.9 lpm) 6027PW, 9032PW, 2 times the rated 1340PW flow of unit or 8 gpm (30.3 lpm) Inlet garden hose size 5/8” ID (15.9 mm) Maximum inlet garden hose length 50 ft. (15,2 m) English — 19 TROUBLESHOOTING CHART Troubleshooting Chart - Gasoline Powered Pressure Washers Only Symptom Possible Cause(s) Corrective Action(s) Engine will not start 1. No gasoline in fuel tank or 1. Fill the tank with gasoline,open fuel or is hard to start carburetor shut off valve. Check fuel line and carburetor 2. Low oil 2. Check oil level. Fill if necessary 3. Start/Stop switch in stop position 3. Move switch to start position 4. Water in gasoline or old fuel 4. Drain fuel tank and carburetor. Use new fuel and dry spark plug 5. Dirty air cleaner filter 5. Remove and clean or replace 6. Spark plug dirty, wrong gap or 6. Clean, adjust the gap, or replace wrong type 7. Spray gun closed 7. Trigger spray gun 8. Other causes 8. See engine owner’s manual Engine misses or 1. Partially plugged air cleaner filter 1. Remove and clean or replace lacks power 2. Spark plug dirty, wrong gap or 2. Clean, adjust the gap, or replace wrong type 3. Drain fuel and carburetor. Use new 3. Bad Fuel fuel. Low pressure and/or 1. Worn or wrong size tip 1. Replace with tip of proper size pump runs rough 2. Inlet filter on pump clogged 2. Clean. Check more frequently 3. Worn water seals, abrasives in 3. Check filter. Replace water seals. See water, or natural wear service center 4. Fouled or dirty inlet or discharge 4. Clean inlet and discharge valve valves assemblies. Check filter 5....
Este manual também é adequado para os modelos :Equipamento de lavagem - 1340PW (4.55 mb)
Equipamento de lavagem - 9032PW (4.55 mb)