Assessments - 5, GPA: 4.6
(
)
)
|
Facilidade de uso
Locate and remove from box, the parts box, which includes gun, handle, wand,oil, knobs and J bolts. Next remove the parts bag and the handle. • Cut carton along dotted lines. • Remove all carton inserts. • Roll unit through opening in carton. NOTE: The high pressure and chemical hose are located at the bottom of the box. Preparing the Pressure Washer for First Use • Note: Included with your pressure washer is a video tape on how to prepare your unit for operation. It is recommended you view this tape before performing the next steps. 1. • Insert handle onto frame. • Slide J bolts into frame. • Tighten knobs turning in clockwise direction. 2. • Remove wood plank from the frame of the unit. An adjustable wrench is required. Discard nut, bolt and board. 3. • Mount the rubber isolator to the frame. To moun isolator place threaded end of bolt through the washer. Next with washer on bolt, place threadet end of bolt through the rubber isolator. Place threaded portion of isolator through the front hole location where the wood plank was mountec on to the pressure washer. Next place lockwashe over threaded portion of nut that has been placet through the mounting hole in the pressure washei and use nut to tighten isolator to the frame. Tighten nut with an adjustable wrench. All isoiatoi parts are supplied in parts bag. 4. • Connect wand with nozzle extension to gun. To tighten, turn knob in clockwise direction. Hand tighten. A CAUTION: Failure to replace the plug will result in serious pump damage. . • Connect chemical hose to the chemical injector hose barb on pump. • Cut tie wrap off of high pressure hose. Unwind high pressure hose to attach the threaded end to the gun. 8. • Your units pump is shipped with a temporary plug that must be replaced with a breather cap. This plug is located over the pump’s oil port. Unscrew and remove this plug. Remove the breather cap from the bag attached to the plug and install it in the pump’s oil port. 9. • Place assembled gun and wand on pressure handle bracket as shown. 7. • Connect high pressure hose to the quick connect outlet on pressure washer. QUICK CONNECT Checklist Before going any further please review the following: NOTE: Always keep hose away from engine , , .. . , muffier • Be sure you have completed assembly instruction. • Double check all fittings to be sure they are tight. IMPORTANT: Before any attempt to start your pressure washer be sure to check engine oil (See Operation under Engine Oil, page 9.) CHEMICAL INJECTOR HOSE PUMP 7 OPERATION Know Your High Pressure Washer PUMP- Develops high pressure. ENGINE OIL FILL- Place where engine oil is poured. PRESSURE REGULATOR- Allows you to adjust the pressure of the outlet stream. ENGINE RUN/STOP SWITCH- Sets engine in starting mode for recoil starter — Stops running engine. RECOIL STARTER- Used for starting the engine manually. SPRAY GUN ASSEMBLY- Controls the application of water onto cleaning surface with trigger device. PUMP OIL FILL- Port where pump oil is poured and breather cap is located. GAS TANK/CAP- Cap is removed and unleaded gasoline is poured. CHEMICAL INJECTION TUBE AND FILTER- Mixes water and detergent in outlet water flow. HIGH PRESSURE OUTLET- Connection for high pressure hose. CHOKE- Lever used for starting unit. Read this Owner’s Manual and Safety Rules before operation of your High Pressure Washer Compare this illustration with our pressure washer to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. 8 topping Your Pressure Washer 4 CAUTION: Do not run pump without the water supply connected and turned on. Failure to do so will result in pump damage. To turn pressure washer off place the on/stop switch to the stop position. Simply shutting OFF engine will not release pressure in the system. Squeeze the trigger on the spray gun for about 3 seconds to relieve pressure. Spray stream will decrease in length. MPORTANT: This unit is equipped with a thermal relief alve. If unit Is allowed to run for several minutes without pressing the trigger on the spray gun, several Irops of water may be released through this valve to ;ool the unit. The heated water will be purged from the )ottom of the pump. To operate the engine you will need to do the following. A CAUTION: Always check engine oil level before every start. Running engine low of oil or out of oil could result in serious damage. A CAUTION: Always check pump oil level before every start. Running pump low on oil could result in pump damage. Adding Pump Oil Before running the high pressure washer, check the pump oil level by viewing the sight glass on the side of the pump. When properly filled, the oil will be at the half way point marked by the two triangles. Your pressure washer pump is shipped with oil. Add oil only if oil level is lower than the half way point on the sight glass. Do not overfill. Use 30 weight non-detergent oil if nece...
Este manual também é adequado para os modelos :Equipamento de lavagem - MGP-678250A (2.11 mb)