Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
Always leave room for expansion. • Use regular UNLEADED gasoline with the pressure washer engine. Regular leaded gasoline may also be used if UNLEADED is not available. Fuel tank capacity is 1 U.S. quart. IMPORTANT: It is importantto prevent gum deposits from forming in essential fuel system parts such as the carburetor,fuel filter, fuel hose or tank during storage. Also, experience indicatesthat alcohol-blended fuels (called gasohol, ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage.Acidic gas can damage the fuel system of an enginewhilein storage.To avoidengine problems,the fuel systemshouldbeemptiedbeforestorageof30 days or longer. See "Storage" on page 15. Never use engine or carburetorcleaner productsin the fuel tank or permanent damage may occur. • Clean area around fuel fill cap, remove cap. • Add "UNLEADED" regular gasoline, slowly, to fuel tank. • Installfuel cap and wipe up any spilled gasoline. TO START YOUR PRESSURE WASHER You have assembled your high pressure washer and have prepared the engine for starting. You are now ready to clean your car, boat or the outside of a buildingor whatever you plan to clean: The best way to start your engine-powered pressure washer for the first time is to follow these instructions step-by-step. This startinginformationalso applies whenever you start the engine after you have let the pressure washer sit idle for at least a day. Place the pressure washer in an area close enough to an outsidewater sourcethatcanflowatarateof3 gallons per minute. Connect a garden hose to the water spout. • Checkthatthe highpressurehoseistightlyconnected to the spray gun and to the pump. See ASSEMBLY section for illustrations. • Connect the garden hose to water inlet opening on the pressurewasher pump and turn ON the water. • Reconnectthe wand extension Note: After reconnectingthe wand extension, you may need to squeeze trigger again on pressure washer wand torelievethe airpressurecausedbywaterinletsupply. Water will spew out of the gun in a thin stream. This will make iteasier to pullstartthe engine. • Engage safety latch on spray gun to the ON position. This disables the trigger so you cannot inadvertently actuate a highpressurespray. ON __ OFF WATER INLET Check inlet screen If screen is damaged DO not connect water. • • Set THROTTLE CONTROL LEVER to CHOKE position (see Page 8). Remove the wand extension and squeeze the trigger to purge pump system of air and impurities. • Turn the pressurecontrol knob counterclockwisetwo turnsfrom maximum pressure (see Page 7). • Grasp the starter gripand pull slowly untilyou feel resistance.Then pullrapidlyupto two (2) times. • When engine starts,move the ThrottleControlLever to the FAST position. If engine fails to start, press the trigger to relieve the pressure, set the Throttle Control Lever to FAST position,then pull starter handle slowly untilyou again feel resistance and then pull up to two (2) times rapidly. • Allow engine to run for two minutes before using. • Once engine has started, place Safety Latch in the OFF position. IMPORTANT: An internalthermal relief valve has a maximum temperature setting of 140°F (60°C). If you run the pump for 5 minuteswithoutpressingthe triggeronthe spraygun, 1/2 to I ounce of water is released through the valve to cool the unit. The small amount of water will dripout the bottom of pump. SIPHONING we recommendthatyou DO NOT siphon-yourwater supply. Connect only to householdwater supply. TIPS • Never use the garden hose inlet to siphon detergent or wax. • If you have the spray nozzle too far away, the cleaning will not be as effective. I0 CUSTOMER RESPONSIBILITIES than30days. MAINTENANCE SCHEDULE FILL IN DATES AS YOU COMPLETE REGULAR SERVICE HOURLY OPERATING INTERVAL MAINTENANCE TASK Every25 Every50 Every100 Before Each Hours or Hours or Hours or Use Yearly Yearly Yearly SERVICE DATES PRESSUREWASHER Check/cleanscreenwaterinletonquick-connect. Checkhighpressurehose. Xt X Checkdetergenthose. X Checkspraygunandassemblyfor leaks. X Purgepumpofairandcontaminants. X ENGINE Checkoillevel. X Change engine oil. _: X* Service aircleaner. X** Clean/replace spark plug. I I I X Prepare for storage. Prepare unit for storage if itisto remainidleforlonger t Cleanifclogged. Replace if perforated. :_ .Change oilafterfirst8 hoursofoperationthenafterevery50hours. * Changesoonerwhenoperating under heavy loador high ambient temperature. ** Cleanmoreoftenunderdirty or dusty conditions. GENERAL RECOMMENDATIONS PRODUCT SPECIFICATIONS Pressure Washer Specifications The warranty of the high pressure washer does not cover items that have been subjected to operator PRESSURE 2250 psi abuse or negligence. To receive full value from the FLOWRATE 2.2 GPM warranty, operator must maintain high pressure washer as instructed in this manual. DETERGENTMIX Use undiluted deterqent Some adjustments will need to be made periodically WATER SUPPLY to properly maintain your high pressure,washer. TE...