Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
NEVER connect it to a hot water supply as it will significantly reduce the life of the pump. • NEVER store the pressure washer outdoors or where it could freeze. The pump will be seriously damaged. • Release trigger when changing from high to low pressure modes. Failure to do so could result in damage Keep hose away from sharp objects. Bursting hoses may cause injury. Examine hoses regularly and replace if damaged. Do not attempt to mend a damaged hose. Garden Hose Connection Instructions 1. Attach swivel adapter to pump water inlet, if not already attached. Notice the swivel adapter is marked with the words pump and hose. Make sure to connect pump side of adapter to pump water inlet to prevent damage to the threads. 2. Attach garden hose to swivel adapter side marked hose. Garden Hose Swivel Adapter Figure 2 - Garden Hose Connection 3. The spray gun should be locked into the "OFF" position by locating the safety trigger lock just above the trigger of the gun. Activate the lock by holding the gun and push the lock from left to right. Squeeze trigger to make sure the trigger does not move. The safety trigger lock should be locked at all times when pressure washer is not in use. Power Cord 1. Plug the power cord into a grounded 120V outlet and press the reset button as shown in Figure 3. 2. THIS MUST BE DONE EACH TIME THE UNIT IS PLUGGED IN AN OUTLET. Reset Figure 3 - Grounded plug/reset button 5 32 Sp Operating Instructions and Parts List PW1600 System Connection 1. Insert lance into the gun and turn clockwise to positive stop as shown in Figure 4. Figure 4 - Gun/Lance Connection 2. Attach the high pressure hose onto the gun by turning clockwise and tighten with a wrench. 3. Be sure that the power switch is in the “OFF” position. 4. Attach the high pressure hose onto the pump water outlet by turning clockwise and hand tightening. 5. Connect garden hose as explained under Garden Hose Connection Instructions. 6. Plug the power cord into a grounded 120V outlet. 7. Turn water on. 8. Unlock trigger lock by moving lock right to left. 9. Depress and hold the trigger on the gun for one minute to release pressure and remove any air trapped in the system. 10.Turn the “ON/OFF” switch to the “ON” position. 6 How to Avoid Damaging Surfaces Directions for Use Damage to cleaning surfaces occurs because the impact force of the water exceeds the durability of the surface. You can vary the impact force by controlling the nozzle’s fan pattern, the nozzle’s angle to the cleaning surface, and the nozzle’s distance from the cleaning surface. Never use a narrow high impact stream or a turbo nozzle on a surface that is susceptible to damage. Avoid spraying windows with a narrow high impact stream or turbo nozzle. Doing so may break the window. The surest way to avoid damaging surfaces is to follow these steps: 1. Before triggering the gun, adjust the nozzle to a wide fan pattern. 2. Place the nozzle approximately 4-5 feet away from the cleaning surface. Then hold the nozzle at a 45° angle to the cleaning surface. Trigger the gun. 3. Vary the fan pattern spray angle and the distance to the cleaning surface until optimum cleaning efficiency is achieved without damaging the surface. Nozzle Cleaning Instructions A clogged or partially clogged nozzle can cause a significant reduction of water coming out of the nozzle and cause the unit to pulsate while spraying. To clean out the nozzle: • Turn off unit. • Turn off water supply. Relieve any pressure trapped in the hose squeezing trigger 2-3 times. Instrucciones de montaje y lista de piezas PW1600 DETERGENTES El uso de detergentes puede reducir radicalmente el tiempo de limpieza y ayudar a eliminar las manchas resistentes. Algunos detergentes han sido disenados especificamente para usar con lavadoras a presion en tareas de limpieza especificas. Estos detergentes tienen una densidad aproximadamente igual a la del agua. El uso de detergentes mas espesos, como jabon para vajilla, obstruira el sistema de inyeccion de productos quimicos y evitara la aplicacion del detergente. La potencia de limpieza de los detergentes depende de su aplicacion a una superficie y el tiempo de espera para que los productos quimicos actuen sobre la suciedad y el tizne. Los detergentes funcionan mejor cuando se aplican a baja presion. La combinacion de la accion de los productos quimicos y el enjuague de alta presion es muy eficaz. En superficies verticales, aplique el detergente comenzando desde abajo y avanzando hacia arriba. Esto evitara que el detergente se escurra hacia abajo dejando marcas. El enjuague de alta presion tambien se debe realizar desde abajo hacia arriba. En manchas particularmente resistentes, puede ser necesario usar un cepillo conjuntamente con los detergentes y el enjuague de alta presion. Operacion 1. Durante el funcionamiento, la presion afecta la lanza: tengala firmemente con ambas manos y apunte la boquilla hacia el suelo. 2. Accione jalando el gatillo de l...