Assessments - 1, GPA: 5
(
)
)
|
Facilidade de uso
© 2003 Campbell Hausfeld IN463600AV 12/03 Specifications PW1686 2640 1650 psi 1.6 GPM 14 Amps 120V 100°F 38 lbs. Assembly Instructions Assembly Instructions and Parts List PW1686 1. Attach detergent suction tube to hose barb on detergent tank and put cap on detergent tank (Figure 1). 2. Slide accessory storage bracket onto back of pressure washer (Figure 1). 3. Slide cord holder and lance storage collar onto side of pressure washer (Figure 1). 4. Align handle on back of pressure washer and attach using screws provided (Figure 1). 5. Assemble one wheel to axle and slide through back of pressure washer and detergent tank (Figure 2). Figure 1 1 2 3 3 4 NOTE: REFER TO PRODUCT MANUAL FOR ALL SAFETY INSTRUCTIONS For parts, product & service information visit Max Pressure Motor Maximum with Power Inlet Cleaning Standard Maximum (Single Water Unit Model Power Lance Capacity Phase) Voltage Temp. Weight Figure 2 Assembly Instructions and Parts List PW1686 2 Assembly Instructions (Continued) 6. Assemble second wheel to axle (Figure 3). 7. Attach hose holder with screws provided (Figure 4). 8. Attach lance storage holder with screw provided (FIgure 5). 9. Align hub cap locking tabs with wheels and press into place (Figure 5). Figure 4 Figure 5 Figure 3 Garden Hose Connection GARDEN HOSE CONNECTION INSTRUCTIONS 1. Attach nipple adapter to inlet fitting on the unit (this may already be attached to the pump). 2. Attach quick connect fitting to garden hose. 3. Pull side “A” of quick connect fitting toward garden hose and push onto nipple adapter. 4. Push side “A” of quick connect fitting towards nipple adapter and release. "A" Figure 6 - Garden Hose Connection Quick Connect Fitting Garden Hose Nipple Adapter ! IMPORTANT ! This pressure washer is equipped with a microswitch sensitive to water flow. This Instant Start/Stop switch (ISS) senses water flow in the pump. When the trigger is released, water stops flowing through the pump. The ISS then automatically turns the motor off to protect pump from overheating. OPERATION 1. Pull trigger on gun. 2. Turn the “ON/OFF” switch to “ON”. 3. Release trigger. The pressure washer motor will stop running. 4. To spray again, pull trigger and motor and pump will restart. Note: Occasionally the motor may run for a short time to bring fresh, cool water into the pump even if trigger is released. This is part of normal operation and will not damage the unit. Always turn the “ON/OFF” switch to “OFF” then trigger gun to release hose pressure before unplugging power cord. Risk of equipment damage. Always make sure the “ON/OFF” switch on the unit is “OFF” and unit is unplugged prior to storage. Risk of Injection. Unit will start spraying when trigger is squeezed if on/off switch is in “ON” position. Always point gun in safe direction. ! WARNING ! CAUTION ! CAUTION Call 1-800-330-0712 for Technical Service Assembly Instructions and Parts List PW1686 3 Power Cord 1. Plug the power cord into a grounded 120V outlet and press the reset button as shown in Figure 7. 2. THIS MUST BE DONE EACH TIME THE UNIT IS PLUGGED IN AN OUTLET. Reset Figure 7 - Grounded plug/reset button Assembly Instructions and Parts List PW1686 System Connection 1. Insert lance into the gun and turn 4. Connect garden hose as explained clockwise to positive stop as shown in under Garden Hose Connection Figure 8. Instructions. Figure 8 - Gun/Lance Connection 2. Ensure that the power switch is in the “OFF” position. 3. Attach the high pressure hose and gun assembly to the unit. 5. Plug the power cord into a grounded 120V outlet, that is on a dedicated circuit. 6. Turn water on. 7. Depress and hold the trigger on the gun for one minute to release pressure and remove any air trapped in the system. 8. Turn the “ON/OFF” switch to the “ON” position. NOTE: REFER TO PRODUCT MANUAL FOR OPERATING INSTRUCTIONS 13 mmOUTLET INLET Gun High Pressure Hose On/Off Switch Garden Hose Figure 9 4 Assembly Instructions and Parts List PW1686 1 Adjustable pressure lance PM271080SV 1 2 Turbo lance PM022621AV 1 3 Hose PM243600AV 1 4 Gun PM037201SJ 1 5 Nipple adapter PM022100AV 1 6 Quick connect fitting PM020600SV 1 7 Tip cleaner PM008500AV 1 8 Handle PM271000SV 1 9 Hardware pack PM271010SV 1 10 Lance storage collar PM271020SV 1 11 Accessories storage bracket PM271030SV 1 12 Lance storage holder PM271040SV 1 13 Hose holder PM270050SV 1 14 Detergent tank cap PM060000SV 1 15 Detergent tank PM271050SV 1 16 Wheel cover PM066300SV 2 17 Wheel PM066301SV 2 18 Axle PM271060SV 1 19 Cord holder PM271070SV 1 20 O-ring PM232200SV 1 1 4 3 2 5 6 7 5 For Replacement Parts, Call 1-800-330-0712 Replacement Parts List Please provide following information: -Model number -Serial number (if any) -Part description and number as shown in parts list Address parts correspondence to: The Campbell Group / Parts Dept. 100 Production Drive Harrison, OH 45030 U.S.A. Ref. Part No. Description Number Qty. 20 8 ...