Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
operation • Replace spark plug. Each 100 hours of • Replace paper air cleaner operation or every 3 cartridge months • Change engine oil. engine Oil Type SAE 10W-30 SAE 30W (Above 60° F) engine Oil Capacity Honda Engines 18 5 fl oz engine Fuel Capacity Honda Engines 0 29 gal Pump Oil Type Wobble Pumps SAE30W non-detergent oil Pump Oil Capacity Vertical Wobble Pumps 2 7 fl oz Pump Detergent Suction Water to detergent ratio 8 to 1 (12% detergent) Water Supply requirements Minimum inlet pressure 20 psi Maximum inlet pressure 100 psi Maximum inlet temperature 100° F Minimum inlet flow rate 5 gpm Inlet garden hose size 5/8 inch I D Maximum inlet garden hose length 50 feet Service record Date Maintenance performed replacement components required 11 Pressure Washer replacement Parts List — Pump PM343501Sj For replacement parts or technical assistance, Call 1-800-330-0712 Please provide following information: Address any correspondence to: -Model number Campbell Hausfeld -Serial number (if any) Attn: Customer Service -Part description and number as shown in parts list 100 Production Drive Harrison, OH 45030 U S A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1920 21 22 24 25 26 27 28 29 30 23 ref. No. Description Part Number Qty. ref. No. Description Part Number Qty. 1 2 Pump Housing Oil Seal Ring l l 0 0 24 25 Piston Guide Body Oil Seal Ring PM270306SV 1 3 3 Bearing l 0 26 Oil Seal Spacer 3 4 Wobble Plate l 0 27 Seal Ring Seat 3 5 Thrust Shoe n 1 28 Water Seal 3 6 Ball Bearing n 1 29 Brass Swivel Assembly PM041360SJ 1 7 Bearing Disk n 1 30 Engine Mounting Bolt MJ102302AV 1 8 Suction Valve Assembly s 3 replacement Kits 9 10 11 12 13 14 15 High Pressure Valve Assembly Thermal Relief Valve Piston Piston Spring O-Ring -67 x 2 5 O-Ring -17 x 3 x 2 62 O-Ring -11 1 x 1 78 s PM345016SJ t t u u u 1 1 3 3 1 1 3 l n s t u Housing Assembly Ball Bearing Assembly Valve Assembly Piston Kit O-ring Kit Detergent Injector Kit Unloader Assembly Kit Seal Kit — PM270300SV PM270301SV PM270302SV PM270303SV PM270210SV PM270304SV PM270307SV 16 Hose Barb 1 17 Unloader Valve Assembly 1 18 Spring 1 19 Chemical Injector Assembly 1 20 Compensation Valve Assembly 1 21 22 Pin Head, Brass PM270305SV 2 1 Oil capacity: 2 7 fl oz OIl type: SAE 30W (non-detergent) 23 Head Bolt PM345213SV 1 12 s sss lns lllln Torque Specifications (in lbs) ref. No. Description Torque 10 Thermal relief valve 110 23 Head Bolt 110 16 Hose Barb Torque 100 n 13 Pressure Washer For replacement parts or technical assistance, Call 1-800-330-0712 Please provide following information: Address any correspondence to: - Model number Campbell Hausfeld - Serial number (if any) Attn: Customer Service - Part description and number as shown in parts list 100 Production Drive Harrison, OH 45030 U.S.A. Replacement Parts List — Vertical Shaft Pressure Washer Ref. No. Description Part No. Qty. 1 Handle tube PM344777SJ 1 2 Frame PM344765SJ 1 3 Flat washer * PM002000AV 6 4 1/4 inch - 20 nylon lock nut * ST073808AV 3 5 1/4 inch - 20 bolt (base) * PM001902AV 3 6 Rubber bumper AL062300AV 2 7 1/4 inch - 20 x 3/4 self tapping screw * MJ102100AV 2 8 Wheel WA120101AV 2 9 Pushnut (2) PM344775SJ 2 10 Baseplate PM344725BR 1 Ref. No. Description Part No. Qty. 11 Detergent tube (not shown) PM013800AV 1 12 Gun PM005140AV 1 13 O-ring (gun) (not shown) PM245800SV 1 14 Hose PM005015AV 1 15 Star Knob (2 pcs.) PM344773SJ 2 16 Carriage Bolt (2 pcs.) PM344774SJ 2 17 Lance, Hi/Low adj fan PM243050AV 1 * Item available at local hardware store 1 2 5 7 6 7 8 9 12 13 14 10 3 4 16 15 17 Pressure Washer Troubleshooting Chart -Gasoline Powered Pressure Washers Only Symptom Possible Cause(s) Corrective Action Engine will not start or is hard to start 1 No gasoline in fuel tank or carburetor 2 Low oil 3 Start/Stop switch in stop position 4 Water in gasoline or old fuel 5 Dirty air cleaner filter 6 Spark plug dirty, wrong gap or wrong type 7 Spray gun closed 8 Other causes 1 Fill the tank with gasoline, open fuel shut off valve Check fuel line and carburetor 2 Check oil level Fill if necessary 3 Move switch to start position 4 Drain fuel tank and carburetor Use new fuel and dry spark plug 5 Remove and clean or replace 6. Clean, adjust the gap, or replace 7 Trigger spray gun 8 See engine owner’s manual Engine misses or lacks 1 Partially plugged air cleaner filter 1 Remove and clean or replace power 2 Spark plug dirty, wrong gap or 2. Clean, adjust the gap, or replace wrong type Low pressure and/or pump runs rough 1 Worn or wrong size tip 2 Inlet filter on pump clogged 3 Worn water seals, abrasives in water, or natural wear 4 Fouled or dirty inlet or discharge valves 5 Restricted inlet 6 Worn inlet or discharge valves 7 Leaking high pressure hose 8 Pump drawing in air 9 Unloader valve seat faulty or worn 1 Replace with tip of proper size 2 Clean Check more frequently 3 Check filter Replace water seals See service center 4 Clean inlet and discharge valve assemblies Check filter 5...