Assessments - 4, GPA: 3.5
(
)
)
|
Facilidade de uso
Improper control of gun/wand can result in injuries to self and others. HAZARD RISK OF INJURY FROM SPRAY WHAT CAN HAPPEN HOW TO PREVENT IT • Always wear ANSI approved Z87 safety glasses.Wear protective clothing to protect against accidental spraying. • Never point wand at, or spray people or animals. • Always secure trigger lock when wand is not in service to prevent accidental operation. • Never permanently secure trigger in pull back (open) position. • High velocity fluid spray can cause objects to break, propelling particles at high speed. • Light or unsecured objects can become hazardous projectiles. CARTON CONTENTS Operation Manual Nozzle Cleaning Tool Chemical Hose Nozzle Holder Quick Connect Nozzles Formed Rubber Covers Engine Frame and Wheel Assembly Engine Manual Bagged Parts Spray Gun High Pressure Hose Engine Oil Quick Connect Spray Wand Handle ASSEMBLY INSTRUCTIONS 1. Place handle assembly onto frame, depress the snap buttons, and slide the handle assembly onto the frame until snap buttons snap into place. 6. Slide the formed rubber covers onto the handle's on-board hose and wand storage. 7. Add engine oil (supplied) to engine. Refer to Engine Owners Manual supplied by engine manufacturer for correct procedure. NOTE: There will be a slight amount of oil in the engine from factory testing. 2. Attach high pressure hose to gun. Tighten securely. 3. Connect wand to gun. Tighten securely. NOTE: The high pressure pump was filled with oil at the factory. There is no need to add oil at this time, see the Maintenance section of this manual for Maintenance information. 4. Place the nozzle holder onto the panel (located on the handle assembly) and push each nozzle holder into place. 5. Remove five colored quick connect nozzles from plastic bag and insert them into correct grommet on the nozzle holder. NOTE: Nozzles are color coded to match colored nozzles on panel. OPERATING INSTRUCTIONS Compare the illustrations with your unit to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. Spray Gun Quick Connect Spray Wand Engine High Pressure Hose High Pressure Pump BASIC ELEMENTS OF A PRESSURE WASHER High Pressure Pump: Increases the pressure of the water supply. Engine: Drives the high pressure pump. High Pressure Hose: Carries the pressurized water from the pump to the gun and spray wand. Spray Gun: Connects with spray wand to control water flow rate, direction, and pressure. Quick Connect Spray Wand: Allows the user to quickly change out high- pressure nozzles. See How To Use Spray Wand instructions in this section. Chemical Hose (not shown): Feeds cleaning agents into the pump to mix with the water. See How To Apply Chemicals/Cleaning Solvents instructions in this section. BASIC ELEMENTS OF AN ENGINE Refer to the engine manual for location and operation of engine controls. Choke Control: Opens and closes carburetor choke valve. Throttle Control Lever: Controls engine speed. Starter Grip: Pulling starter grip operates recoil starter to crank engine. Fuel Valve Lever: Opens/closes connection between fuel tank and carburetor. Engine Switch: Enables and disables ignition system. PRESSURE WASHER TERMINOLOGY PSI: Pounds per Square Inch. The unit of measure for water pressure. Also used for air pressure, hydraulic pressure, etc. GPM: Gallons Per Minute. The unit of measure for the flow rate of water. CU: Cleaning Units. GPM multiplied by PSI. GPM x PSI = CU Bypass Mode: Allows water to re-circulate within pump when the gun trigger is not pulled. Allowing the unit to run for more than two minutes without the gun trigger pulled could cause overheating and damage to the pump. Thermal Relief Valve: When the temperature inside the pump rises too high the valve will open and release a gush of water in an effort to lower the temperature inside the pump. The valve will then close. Chemical Injection System: Mixes cleaners or cleaning solvents with the water to improve cleaning effectiveness. Water Supply: All pressure washers must have a source of water. The minimum requirements for a water supply are 20 PSI and 5 gallons per minute. PRESSURE WASHER OPERATING FEATURES PRESSURE ADJUSTMENTS The pressure setting is preset at the factory to achieve optimum pressure and cleaning. If you need to lower the pressure, it can be accomplished by these methods. 1. Back away from the surface to be cleaned. The further away you are, the less the pressure will be on the surface to be cleaned. 2. Change to the 40. nozzle - (white) this nozzle delivers a less powerful stream of water and a wider spray pattern. DO NOT attempt to increase pump pressure. A higher pressure setting than the factory set pressure may dam...
Este manual também é adequado para os modelos :Equipamento de lavagem - A07513-0412-0 (1.55 mb)
Equipamento de lavagem - A07513-0412-0 (1.55 mb)
Equipamento de lavagem - A07513-0412-0 (1.55 mb)
Equipamento de lavagem - A07513-0412-0 (1.55 mb)