Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
(Refer to the engine’s operating manual for seasonal grades.). We recommend that the oil be changed after the first 5 hours of use, then once every 50 hours. • STEP 2: Fill gas tank with unleaded gasoline. Do not use leaded gasoline. • STEP 3: Connect the high pressure hose to the unit’s high pressure outlet. • STEP 4: Connect garden hose to unit’s water inlet. Connect garden hose to the cold water source and turn water on completely. Do not use hot water. • STEP 6: Unlock the Safety lock. Trigger the gun to eliminate trapped air, wait for a steady flow of water to emerge from the spray nozzle. • STEP 7: Open fuel valve. Pull the choke rod to the ON position (on a warm engine, leave the choke rod in the OFF position). • STEP 8: Move the engine stop switch to the ON position. For engine details see engine manual. • STEP 9: Pull the starter handle. If the engine fails to start after 3 pulls, squeeze the trigger gun to release pressure, and repeat step. After the engine warms up enough to run smoothly, move choke rod to OFF position. English 7 USING THE ACCESSORIES USING THE ACCESSORIES Quick connect nozzles The color-coded quick connect nozzles provide a wide array of spray widths from 0° to 65° and are easily accessible when placed in the convenient rubber nozzle holder. 0° spray angle = Red nozzle For particularly stubborn accumulation of grime. Not recommended for soft materials like sidings, decks, painted surfaces, cars. 25° spray angle = Green nozzle For dirt accumulation over a large surface. 40° spray angle = White nozzle For moderate dirt accumulation over a large surface. 65° spray angle = Black detergent nozzle For operating with detergent or cleaning with negligible pressure. . WARNING High pressure in nozzle area. Risk of injury caused by improperly locked nozzle. • Make sure you hear a ‘click’ when inserting the nozzle tip into the wand. • Pull the nozzle to make sure it is seated properly before operating your unit. (See ASSEMBLY INSTRUCTIONS: Step 6 and Step 7) . WARNING To avoid serious injury never point spray nozzle at yourself, other persons or animals. 8 English WORKING WITH DETERGENTS WORKING WITH DETERGENTS Detergents can only be applied with the black detergent nozzle. • STEP 1: Install the black detergent nozzle for detergent application at low pressure. • STEP 2: Fill a container with Karcher detergent. Place the filter end of detergent suction tube into the container. • STEP 3: With the engine running, pull trigger to operate unit. Liquid detergent is drawn into the unit and mixed with water. Apply detergent to work area. Do not allow detergent to dry on surface. • STEP 4: Always draw fresh water through the detergent suction tube when the cleaning job is done, to rinse/flush any remaining detergents from the injection system. For best results see Cleaning Tips for specific information on how to clean different surfaces. Detergents . CAUTION This unit has been designed for use with cleaning detergents recommended by the manufacturer. The use of other cleaning detergents may affect the operation of the machine and void the warranty. Always Use Karcher Detergent for Best Results Karcher biodegradable detergents are specially formulated to protect the environment and your pressure washer. The special formula won’t clog the suction tube filter and will protect the internal parts of the pressure washer for a longer life. For Karcher Detergents, check your retailer or visit our website: Karcher detergents available in USA / Mexico: – All Purpose & Vehicle Cleaner – Exterior House Cleaner – Deck & Patio Cleaner – Heavy Duty Degreaser Karcher detergents available in Canada: – Vehicle Wash – Pressure Wash – Deck & Fence Wash – Degreaser . CAUTION Never use: – Bleach, Chlorine products and other corrosive chemicals – Liquids containing solvents (i.e., paint thinners, gasoline, oils) – Tri-sodium phosphate products – Ammonia products – Acid-based products These chemicals will harm the unit and will damage the surface being cleaned. English 9 TAKING A BREAK ..five minutes or more TAKING A BREAK ..five minutes or more • STEP 1: • STEP 2: Move the engine stop switch to the Release trigger and engage gun OFF position. safety lock. For engine details see engine manual. SHUTTING DOWN & CLEAN-UP • STEP 1: Remove detergent suction tube from container and insert into 1 gallon of fresh water. Siphon water at low pressure for one minute. • STEP 2: Move the engine stop switch to the OFF position. Close the fuel valve. • STEP 3: Turn off the water source. • STEP 4: Press trigger to release water pressure. • STEP 5: Release trigger and engage gun safety lock. • STEP 6: Disconnect the garden hose from the water inlet on the unit. • STEP 7: Disconnect the high pressure hose from the high pressure outlet. WINTERIZING AND LONG-TERM STORAGE • 1: Disconnect all water connections. • 2: Turn on the machine for a few seconds, until the water which had remained in the pump exits, turn off imm...