Engine dipstick/oil plug - Jauge graduée/Bouchon du réservoir d’huile du moteur - Tapón/varilla para medición del nivel de aceite del motor J. High-pressure pump - Pompe haute pression - Bomba de alta presión K. Engine - Moteur - Motor L. Choke control - Commande d’étrangleur - Control de la estrangulación del carburador M. Starter grip - Poignée de démarrage - Agarradera de arranque N. Fuel valve lever - Levier de la soupape à essence - Palanca de la válvula de combustible O. Engine switch

DPE3800 Pressure Washer • Laveuse à pression • Lavadora a presión AWARNING: Do not operate this unit until you read this instruction manual and the engine instruction manual for safety, operation and maintenance instructions. AAVERTISSEMENT : ne pas utiliser l’appareil avant d’avoir lu le mode d’emploi, et celui du moteur, et l’intégralité des directives de sécurité, d’utilisation et d’entretien. AADVERTENCIA: No opere esta unidad hasta que haya leído este manual de instrucciones y el del mo

• If engine does not start after two pulls, squeeze trigger of gun to relieve pump pressure. Pull starter cord slowly until resistance is felt. Then pull cord rapidly to avoid kickback and prevent hand or arm injury. • Keep children away from the pressure washer at all times. • Do not overreach or stand on an unstable support. • Do not use pressure washer while standing on a ladder. • Grip gun/wand firmly with both hands. Expect the gun to kickback when triggered. DANGeR: RISk of INjuRy oR PRoPe

Latin America: This warranty does not apply to products sold in Latin America. For products sold in Latin America, see country specific warranty information contained either in the packaging, call the local company or see website for warranty information. FREE WARNING LABEL REPLACE MENT: If your warning labels become illegible or are missing, call 1-800-4-DeWALT for a free replacement. Glossary Bypass mode: Allows water to re-circulate within pump when the gun trigger is not pulled. chemical hos

To remove Tires 1. Using a 1/8" hex head wrench loosen set screw in hub collar. 2. Slide hub collar from axle and remove the tire. STorAGE Engine U Consult the engine instruction manual for the manufacturer's recommendations for storage. Pump The manufacturer recommends using a pump protector/winterizer, such as DeWALT winterizer (DP80) when storing the unit for more than 30 days and/or when freezing temperatures are expected. DeWALT winterizer (DP80) is availabe at the store where the pressure

Si tiene dudas o comentarios, contactenos. InstructIon ManuaL GuIDe D'utILIsatIon ManuaL De InstruccIones INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO Y POLIZA DE GARANTIA.aDVertencIa: LEASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. 1-800-4-DeWALT • DP2800 Pressure Washer Laveuse a pression Lavadora a presion English Specifications MODEL WEIGHT HEIGHT WIDTH Length PSI Max* Op erating PSI GPM Max* Op erating GPM Engi ne DP2800 97 lbs 26.5" 23" 40" 2800 2520 3.0 2.7 Honda 6.5 Hp GX200 * Water f

The thermal relief valve will then close. If pump is left in bypass mode for more than two minutes internal components of the pump can be damaged. Start-up Procedure 1. In a well-ventilated outdoor area, add fresh, high-quality, unleaded gasoline with a pump octane rating of 86 or higher. Do not overfill. Wipe up spilled fuel before starting the engine. Refer to engine instruction manual for correct procedure. 2 . Check engine oil level. Refer to the engine instruction manual for correct procedu

• Improperly stored fuel could lead to acciden tal ignition. Fuel im prop erly secured could get into the hands of children or oth er un qual i fied persons. • Use of acids, toxic or cor ro sive chemicals, poisons, in sec ti cides, or any kind of flam ma ble solvent with this product could re sult in se rious injury or death. live plants) that could be damaged from muffler exhaust heat. • Store fuel in an OSHAap proved con tain er, in a se cure location away from work area. • Do not spray flamma

Leaks caused by loose fittings or worn or damaged hoses can result in injection injuries. DO NOT TREAT FLUID INJECTION AS A SIMPLE CUT! See a physician immediately! WARNING: Risk of fire, asphyxiation and burning. NEVER fill fuel tank when engine is running or hot. Do not smoke when filling fuel tank. • Never fill fuel tank completely. Fill tank to 1/2" (12.7 mm) below bottom of filler neck to provide space for fuel expansion.Wipe any fuel spillage from engine and equipment before starting engin

1) 1. Place handle assembly (O) onto frame, depress the snap buttons, and slide the handle assembly onto the frame (F) until snap buttons are secured in place. CAUTION: Risk of personal injury. Avoid placing hands between handle and frame when assembling to prevent pinching. F O note: The high-pressure pump was filled with oil at the factory. Always check oil level before using (refer to Maintenance for more information). WARNING: Risk of bursting. Use a tire pressure gauge to check the tires pr