Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Doing so may damage the vehicle’s battery or the multimedia system. • Do not disassemble or modify monitor. Doing so may damage it and void the warranty. • Keep moisture away from the set. Water and humidity may damage the internal circuitry. • Do not let the monitor become overheated. If the temperature inside the vehicle is high or the monitor has been exposed to direct sunlight, lower the monitor’s temperature before use. (The liquid crystal panel operates within a temperature range of -1~45°C (30~113°F). • In extremely cold temperature, the movement of the picture may slow and the picture may become dark. The monitor will work normally once the temperature increase to its normal operation range. • Small black or shiny dots may been see inside the liquid crystal panel. These are normal when manufacturing liquid crystal products. Description of Button And Connectors: 2. Dimmer Sensor 3. Remote Sensor 4. Picture Controls б. Wide Mode Controls 7. Video Composite Input 8. 2-Pin Molex Power Connector 9. IR Serial Remote OUT 10. 8-Pin RGB input DIN cable 11.Speaker -(White w.Black line) 12.Speaker + (White) ^.Dimmer Lead (Orange) 2 Description b OWNER’S MANUAL Description of Picture Adjustment: • Press the PICTURE SELECT button several times, the screen will display the picture control Bar in the following order sequentially. (BLANK)^ BRIGHTNESS^ CONTRASTS COLOURS TINT^ DIMMER^MEM RESET—, • Before the display disappears, use the PICTURE SELECT UP (VOLUME UP) button or PICTURE SELECT DOWN (VOLUME DOWN) button, to adjust the picture quality. COLOUR Illlllllllinnnnnn —— —— DOWN UP • Press the WIDE/NORMAL button, the screen will display 16:9 or 4:3 picture. • DIMMER : Press UP ' DOWN or Brightness to choose seven different sets. Auto Brightness automatically DASHBOARD Controlled by Dashboard illumination • MEM RESET : Press UP or DOWN, all sets return the initial value. Care And Maintenance: Cleaning the Cabinet: • Use a soft, dry cloth to gently wipe off any dirt. • Do not use benzene, thinner, car cleaner, etc., as these substances may damage the cabinet or cause the point to peel. Cleaning the LCD Panel: • Use a soft, dry cloth to gently wipe off any dust. • The surface is easily scratched, do not rub it with hard objects. Wiring Precautions: Read all wiring precautions. If you are not sure of the connections, contact your authorized Clarion dealer. 1.Disconnect the negative (-) lead from the vehicle’s battery before making any connections. 2.When creating passage holes through metal or plastic, use grommets to Eliminate any sharp edges created during drilling. This will protect power or video wires from nicks or damaged causing a possible short circle or failure. 3.When connecting the ground lead, fasten the ground lead (black) securely to a clean metal plate on the vehicle. Use sandpaper to remote any paint from the surface where the ground terminal is attached. Description of Installation: Now the VMA633 is useable with including mounting bracket. The VMA633 monitor will accept a video signal from any video source with composite video output. The Infrared (IR) sensor will work with a Clarion NAX9500E using the CCE-001 adapter and IR extension cable, which are provided. 3 I § Q UJ S o Clarion VMA633 6.5” TFT LCD Monitor 1. Look over the vehicle for a monitor location. Each vehicle is different and locations will vary. Make sure the monitor will not interfere with the driver's safe operation of vehicle. 2. Once a location has been determined, run the 3.5 mm IR extension, Video Composite and power Molex connector into the monitor's mounting location. 3. Plug main cable into the monitor. 4. Run the IR extension, video, and power cables to their respective destinations. INSTALLATION OWNER’S MANUAL Troubleshooting: Symptom Cause Solution System does not work Fuse is blown. Power wires are not connected. Replace external fuse with the same value. Check the wire connections and Connect it properly. The screen dark. The brightness is adjusted too low. Usage conditions are poor. Check that the brightness is properly adjusted, if not adjust it properly. This may happen if the temperature in the vehicle is below -1°C (30°F) or above 45°C (113°F). Check again when the temperature is between -1°C (30°F) and 45°C (113°F) Specification: General Specifications: Power Requirement: Power Consumption: Weight Dimensions (w x h x d): Included Parts + 12 Volts DC (9-16 Volts DC) 9 watts, Power On 0.8 amps (800mA) 0.5 kg (1.1 lb) 167 x 121 x 29 mm (6-1/2 x 4-7/10 x 1-3/10 in.) LCD Monitor 3.5 mm Male to Male IR extension cable (5m) 2-pin Molex Power connector CCE-001 IR adapter for NAX9500E and/or VS718 Mounting bracket Speaker extension cable (5m) Monitor Specifications: Display Type: Screen Size: Pixels: Screen Resolution: Video Input Level(RCA) RGB Input Level Colour TFT Active Matrix LCD 6.5” (Panel Dimensions 144.4 x 80.3 mm) 1200x234...