Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
page 17) by 50%. Level operation (Connected: ON, Open: OFF) MARKER BACK BLACK*2 Reduces the brightness of the background outside the marker displayed in “GPI PRESET1” (.. page 17) to 0%. Level operation (Connected: ON, Open: OFF) CENTER MARKER Switches the center marker display ON/OFF. (When other markers are being displayed, this is superimposed on the other markers) Level operation (Connected: ON, Open: OFF) INPUT SEL. VIDEO Switches the input system to VIDEO. Edge operation INPUT SEL. Y/C Switches the input system to Y/C. Edge operation INPUT SEL. SDI1 Switches the input system to SDI1. Edge operation INPUT SEL. SDI2 Switches the input system to SDI2. Edge operation INPUT SEL. YPBPR/RGB Switches the input system to YPBPR/RGB. Edge operation SD ASPECT Sets the aspect ratio settings when using SD signal input. (Disabled when using HD signal and PC signal) Level operation (Connected: 16:9, Open: 4:3) SCAN You can switch the scan mode between “UNDER” and “NORMAL”. (Disabled when using PC signal) Level operation (Connected: UNDER, Open: NORMAL) R-TALLY*3 Lights the red tally. Level operation (Connected: ON, Open: OFF) G-TALLY*3 Lights the green tally. Level operation (Connected: ON, Open: OFF) MONO Switches between color and monochrome (MONO). (Disabled when using PC signal) Level operation (Connected: Monochrome, Open: Color) GAMMA SEL. FILM Used to switch the gamma characteristic to the FILM mode. Level operation (Connected: FILM mode, Open: STANDARD mode) GAMMA SEL. STDIO/PST Used to switch the gamma characteristic to the STDIO/PST mode. Level operation (Connected: STDIO/ PST mode, Open: STANDARD mode) RGB SYNC*4 Used to select SYNC at the time of RGB-VIDEO input. Level operation (Connected: EXT, Open: G-ON) *1 When the 16:9 marker and 4:3 marker are simultaneously selected and activated on the 16:9 aspect display, both markers are displayed. *2 When the 16:9 marker and 4:3 marker are simultaneously displayed, the background selected with the 16:9 marker is controlled. *3 When both “R-TALLY” and “G-TALLY” are ON at the same time, the tally color becomes orange. *4 This is only enabled when “RGB-VIDEO” is selected in “YPBPR/RGB” in the “INPUT SELECT” menu. REMOTE Specifications (continued) g Assignment of item priority levels • When both “MARKER1” and “MARKER2” are ON at the same time, “MARKER1” has priority. However, when the display aspect is 4:3, the “MARKER1” aspect is 16:9, and the “MARKER2” aspect is 4:3, “MARKER2” is displayed. In this case, the “MARKER2” background is controlled. • When “MARKER BACK HALF” and “MARKER BACK BLACK” are simultaneously activated, priority goes to “MARKER BACK BLACK”. • When two or more of the following items - “INPUT SEL. VIDEO”, “INPUT SEL. Y/C”, “INPUT SEL SDI1”, “INPUT SEL. SDI2” and “INPUT SEL. YPBPR/RGB” - are simultaneously activated, priority goes to the last item activated. • When “GAMMA SEL. FILM” and “GAMMA SEL. STDIO/PST” are simultaneously activated, priority goes to “GAMMA SEL. FILM”. RS-232C terminal Refer to the following diagram and lower right table for the RS-232C terminal pin arrangement and connections. Please contact the vendor for information about detailed systems which used the RS-232C. PC Side (Straight) BT-LH2600W Side RS-232C Terminal (9P) Pin number Signal Pin number Signal 1 N.C. 1 N.C. 2 RXD 2 TXD 3 TXD 3 RXD 4 DTR 4 DSR 5 GND 5 GND 6 DSR 6 DTR 7 RTS 7 CTS 8 CTS 8 RTS 9 N.C. 9 N.C. RS-232C REMOTE operation method Pin number Signal name Explanation 1 N.C. Not connected 2 TXD Transmission data 3 RXD Reception data 4 DSR Connected inside. 5 GND Ground 6 DTR Connected inside. 7 CTS Connected inside. 8 RTS Connected inside. 9 N.C. Not connected g Connectors and signal names g Command format Connector: D-SUB 9-pin (female) Signal name STX (02h) Command : Data ETX (03h) • Commands are 3 characters following STX, finally adding ETX. • Add a : (colon) after the command as required, and add the data. g Response formats 1. Setting command response STX (02h) Command ETX (03h) 2. Query command response STX (02h) Data ETX (03h) 3. Error response STX (02h) Error code ETX (03h) Signal level Conforms to RS-232C Synchro system Tone pace synchro system Transfer rate 9600 bps Parity None Data length 8 bit Stop bit 1 bit Flow control None Error code g Communication Conditions ER001: Invalid command ER002: Parameter error REMOTE Specifications (continued) g Setting command No Command Explanation Data Response 1 IIS Input switch 0: SDI1 1: SDI2 2: VIDEO 3: YPBPR/RGB 4: Y/C IIS 2 VPC Image quality adjustment CON00-60 : Contrast settings BRI00-60 : Brightness settings CRO00-60 : Chroma settings PHA00-60 : Phase settings VPC 3 OBO Blue only 0: OFF 1: ON OBO 4 OHV HV Delay 0: OFF 1: H DELAY 2: V DELAY 3: HV DELAY OHV 5 DSD Status display 0: CONTINUE 1: 3SEC OFF 2: OFF DSD 6 ISM Analog mode ANA0: YPBPR ANA1: RGB-VIDEO ANA2: RGB-COMP. ISM 7 IRF RGB Sync 0: G-ON 1: EXT IRF 8 DMK Marker settings 16:9 marker MK100: OFF MK101: 80% MK102: 88% MK103: 93% MK104: 95% MK105: 14:...