Assessments - 5, GPA: 3.8
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
(You must remove and reinstall the driver.) If the installation fails If the installation is stopped because the New Hardware Wizard has failed, right-click My computer, and click Properties - System Properties -the Hardware tab. Click on the Device Manager and reinstall the driver by following these steps below. The symbol showing that the device has failed to be installed is displayed as shown in In this case, click “Scan for hardware changes” to run the Setup Wizard again. At this time, if the installation fails, click and right-click it. Select ‘Driver Update’ from the displayed menu. Checking the configuration After the installation, you can check the configuration by following these steps: Right-click My computer, click Properties -System Properties - Hardware tab. Click on Device Manager. A list of installed devices will be displayed, as shown in the figure below. Checking the Web Camera Setup Double-click My Computer on the Windows Desktop. Double-click the USB Video Device #2. You should find that the web camera has been set up normally, as shown in the figure below. Checking the Microphone and Speaker Setup Double-click Sounds and Audio Devices in the Control Panel. Select the Voice tab and click on Test Hardware. If the sound from your monitor is too soft, adjust the volume after setting the volume of your PC to the maximum. Follow the steps described below. You should find that the microphone and speaker have been set up. UC Monitor Limitations This monitor is a UC monitor and therefore when connecting cameras and audio devices to it, cameras and audio devices except for the monitor display are recognized as USB devices and not as a camera or audio device. This monitor must be connected with a D-Sub (Analog) or a DVI-D cable (Digital) when used as a normal monitor. USB cables are used when connecting other devices. For some media players, when a USB device is being recognized again while a media player is running, you have to close and run it again to operate the sound and camera devices normally. For some PCs, your PC may not boot up with the monitor recognized even if the USB cable is connected, depending on the PC BIOS version. Check whether the BIOS on your PC has been updated to the latest version. Because of the characteristics of USB audio devices, the initial volume setting of your UC monitor may be very low. (This may differ depending on the operating system.) At this time, adjust the Master Volume on your PC. USB Monitor Limitations This monitor supports Windows XP Service Pack 2 or later only. Service Pack 1 or earlier is not supported. This monitor is designed for optimal performance using Windows XP Service Pack 2 and USB 2.0. The UC monitor may not work normally with versions earlier than USB 2.0. If you connect multiple UC monitors, the USB devices recognized by these monitors may not work normally. Noise may occur from the MIC and speaker if this monitor is placed too near. Monitor Driver When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown below. Internet web site :(Worldwide) (U.S.A) (Korea) (China) Installing the Monitor Driver (Automatic) Insert the CD into the CD-ROM drive. Click "Windows". Choose your monitor model in the model list, then click the "OK" button. If you can see following message window, then click the "Continue Anyway" button. Then click the "OK" button (Microsoft® Windows® XP/2000 Operating System). This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage Monitor driver installation is completed. Installing the Monitor Driver (Manual) Windows Vista | Windows XP | Windows 2000 | Windows ME | Windows NT | Linux Microsoft® Windows Vista™ Operating System Insert your Manual CD into your CD-ROM drive. Click (Start) and "Control Panel". Then, double-click on "Appearance and Personalization". Click "Personalization" and then "Display Settings". Click "Advanced Settings…". Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the configuration for your monitor is completed. The monitor can be used as is. If the message “Windows needs…” is displayed, as shown in the figure below, click "Continue". This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage Click "Update Driver…" in the "Driver" tab. Check the "Browse my computer for driver software" checkbox and click "Let ...