Assessments - 5, GPA: 4.4 ( )

Fabricante : LG Arquivo Tamanho: 2.55 mb Arquivo Nome : Língua de Ensino:

3 ASSEMBLING AND PREPARING ENGLISH ENG ASSEMBLING AND PREPARING Unpacking Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories. D-SUB Cable DVI-D Cable (This cable is not included in all countries.) CD(Owner's Manual) / Card or ( Depending on the country ) ( Depending on the country ) Power Cord AC-DC Adapter AC-DC Adapter Stand Body Stand Base CAUTION yyDo not use any unapproved accessories to ensure the safety and product life span. yyAny damages or injuries by using unapproved accessories are not covered by the warranty. NOTE yyThe accessories supplied with your product may vary depending on the model. yyProduct specifications or contents in this manual may be changed without prior notice due to upgrade of product functions. ASSEMBLING AND PREPARING 4 ENG ENGLISH Parts and buttons Power Indicator yyLighting On: Turned on yyLighting Off: Turned off (Power Button) Button (See p.11) Connection panel (See p.9) Setting up the Monitor set Attaching the Stand Base 1 Place the Monitor set with the screen side down on a flat and cushioned surface. Detaching the Stand Base 1 Place the Monitor set with the screen side down on a flat and cushioned surface. Pull out the Stand Body and Stand Base from the monitor set. Turn the screw to the left with a coin. Pull out the Stand Base. 2 1 CAUTION 2 Lay a foam mat or soft protective cloth on the surface to protect the screen from damage. 3 Attach the Stand Body to the monitor set. Attach the Stand Base. Tighten the screw to the right with a coin. 2 1 2 Stand Body 3 Stand Body Stand Base Stand Body Stand Base Stand Base CAUTION yyThis illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. yyDo not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. Mounting on a table 1 Lift and tilt the Monitor set into its upright position on a table. Leave a 10 cm (minimum) space from the wall for proper ventilation. 3 Press (Power) button on the bottom switch panel to turn the power on. CAUTION Unplug the power cord before moving the Monitor to another location. Otherwise electric shock may occur. 10 cm 10 cm 10 cm 10 cm Using the cable holder 2 Connect the AC-DC Adapter and Power Cord to a wall outlet. Cable holder or WARNING Using the Kensington security system When you adjust the angle, do not hold the bottom of the Monitor set frame as shown on the following illustration, as may injure your fingers. The Kensington security system connector is located at the back of the Monitor set. For more information of installation and using, refer to the manual supplied with the Kensington security system or visit Connect the Kensington security system cable between the Monitor set and a table. Do not touch or press the screen when adjusting the angle of the monitor. Do not hold this set like below picture.Monitor screen can detach from stand base and injure your body. NOTE The Kensington security system is optional. You can obtain it from most electronics stores. NOTE Tilt from +20 to -5 degrees up or down to adjust the angle of the Monitor set to suit your view. Rear Front Model E1942TCE2042TCE2242TC E2442TC VESA (A x B) 75 x 75 100 x 100 Standard screw M4 Number of screws 4 Mounting on a wall For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide. 10 cm CAUTION 10 cm yyDisconnect the power cord first, and then move or install the Monitor set. Otherwise electric shock may occur. yyIf you install the Monitor set on a ceiling or slanted wall, it may fall and result in severe injury. yyUse only an authorized LG wall mount and contact the local dealer or qualified personnel. yy Do not over tighten the screws as this may cause damage to the Monitor set and void your warranty. yy Use only screws and wall mounts that meet the VESA standard. Any damages or injuries by misuse or using an improper accessory are not covered by the warranty. 10 cm 10 cm If you intend to mount the Monitor set to a wall, attach Wall mounting interface (optional parts) to the back of the set. When you install the Monitor set using a wall mounting interface (optional parts), attach it carefully so it will not drop. 1 Please, Use the screw and wall mount interface in accordance with VESA Standards. 2 If you use screw longer...

Baixe o seu

Para fazer o download, introduza 2 dígitos :