Assessments - 5, GPA: 3.4
(
)
)
|
Facilidade de uso
On Cleaning Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. On Repacking Do not throw away the carton and packing materials. They make an ideal container in which to transport the unit. When shipping the unit to another location, repack it in its original material. On Disposal The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority. A2 A3 Connecting the Display Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Once you connect the stand base, try not to disconnect it. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand 1. Place the monitor with its front facing downward on a soft cloth. 2. Assemble the Stand Body into the product in the correct direction as shown in the picture. Make sure you push it until you hear it “click”. 3. Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction. 4. Once assembled take the monitor up carefully and face the front side REAR REAR REAR REAR FRONT FRONT Stand Body Stand Base Stand Body Connecting the Display To remove the Stand: 1. Put a cushion or soft cloth on a flat surface. 2. Place the monitor face down on the cushion or soft cloth. The Head part The Stand base part 3. Hold the product as it follows and lift up the Stand slightly. 4. Change your hold on the product as it follows and turn the Stand Base in the arrow direction. 5. Pull out the Stand to remove. A4 Connecting the Display To remove the Stand Base: Type. A 1. Ensure there are two short and two long 2. Hold the body of the Stand as it follows. latches at the bottom of the Stand Base. 3. Press inside the two long latches at the 4. Keep pressing the two latches and use the other hand to hold the body of the Stand to push the same time with your strength as it follows. Stand Base in the arrow direction to remove. 5. The body of the Stand and the Stand Base are successfully separated. A5 Connecting the Display To remove the Stand Base: Type. B 1. Ensure there are four latches at the 2. Hold the body of the Stand as it follows. bottom of the Stand Base. 3. Press inside the four latches individually toward each end. 4. Put the Stand Base on a flat surface and pull 5. The body of the Stand and the Stand up the body of the Stand while holding the Base are successfully separated. Stand Base with the other hand. to remove. A6 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5°~20° 20 Warning: When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. You can hurt your finger(s). Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. A7 2 1 Connecting the Display Using the Computer 1. Place the monitor in a convenient, well-ventilated location near your computer. 2. Connect the signal cable. When attached, tighten the thumbscrews to secure the connection. 3. Connect the power cord into a proper power outlet that is easily accessible and close to the display. Signal Cable NOTE of the rear view. This rear view represents a PC MAC Wall-outlet type PC-outlet type Power Cord Analog signal D-sub Varies according to model. 1 2 Mac adapter For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. This is a simplified representation general model; your display may differ from the view as shown. 4. Press button on the front switch panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically. NOTE ‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals. If you want to adjust the monitor while in use, or wish to manually run this function once again, push the ‘AUTO/SET’ button on the front panel of the monitor. Otherwise, you may execute the ‘ Factory reset’ option on the OSD adjustment menu. However, be aware that this option...
Este manual também é adequado para os modelos :Monitores - L194WS-SF (2.27 mb)
Monitores - L204WS-BF (2.27 mb)
Monitores - L204WS-SF (2.27 mb)