Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
Read and follow these instructions when connecting and using your computer monitor: l To protect your display from possible damage, do not put excessive pressure on the LCD panel. When moving your monitor, grasp the frame to lift; do not lift the monitor by placing your hand or fingers on the LCD panel. l Unplug the monitor if you are not going to use it for an extensive period of time. l Unplug the monitor if you need to clean it with a slightly damp cloth. The screen may be wiped with a dry cloth when the power is off. However, never use alcohol, solvents or ammonia-based liquids. l Consult a service technician if the monitor does not operate normally when you have followed the instructions in this manual. l The casing cover should be opened only by qualified service personnel. l Keep the monitor out of direct sunlight and away from stoves or any other heat source. l Remove any object that could fall into the vents or prevent proper cooling of the monitor’s electronics. l Do not block the ventilation holes on the cabinet. l Keep the monitor dry. To avoid electric shock, do not expose it to rain or excessive moisture. l When positioning the monitor, make sure the power plug and outlet are easily accessible. l If turning off the monitor by detaching the power cable or DC power cord, wait for 6 seconds before attaching the power cable or DC power cord for normal operation. l To avoid the risk of shock or permanent damage to the set, do not expose the monitor to rain or excessive moisture. l IMPORTANT: Always activate a screen saver program during your application. If a still image in high contrast remains on the screen for an extended period of time, it may leave an 'after-image' or 'ghost image' on front of the screen. This is a wellknown phenomenon that is caused by the shortcomings inherent in LCD technology. In most cases, the afterimage will disappear gradually over a period of time after the power has been switched off. Be aware, that the afterimage symptom cannot be repaired and is not covered under warranty. l Warning for lifting monitor - Do not use the area underneath the logo cover to grip or lift the monitor. Placing weight on the logo cover can cause it to break away from the body and cause the monitor to fall. When lifting the monitor, place one hand under the monitor's frame. Consult a service technician if the monitor does not operate normally when the operating instructions given in this manual have been followed. RETURN TO TOP OF THE PAGE Installation Locations l Avoid exposure to heat and extreme cold. l Do not store or use the LCD monitor in locations exposed to heat, direct sunlight or extreme cold. l Avoid moving the LCD monitor between locations with large temperature differences. Choose a site that falls within the following temperature and humidity ranges. m Temperature: 0-35°C 32-95°F m Humidity: 20-80% RH l Do not subject the LCD monitor to severe vibration or high impact conditions. Do not place the LCD monitor in the trunk of a car. l Take care not to mishandle this product by either knocking or dropping it during operation or transportation. l Do not store or use the LCD monitor in locations where there is a high level of humidity or in dusty environments. Do not allow water or other liquids to spill on or into the LCD monitor. RETURN TO TOP OF THE PAGE • Safety and Troubleshooting • General FAQs • Screen Adjustments • Compatibility with Other Peripherals • LCD Panel Technology • Ergonomics, Ecology and Safety Standards • Troubleshooting • Regulatory Information • Other Related Information FAQs (Frequently Asked Questions) General FAQs Q: When I install my monitor what should I do if the screen shows 'Cannot display this video mode'? A: Recommended video mode for Philips 20": 1680x1050 @60Hz. 1. Unplug all cables, then connect your PC to the monitor that you used previously. 2. In the Windows Start Menu, select Settings/Control Panel. In the Control Panel Window, select the Display icon. Inside the Display Control Panel, select the 'Settings' tab. Under the setting tab, in box labeled 'desktop area', move the slidebar to 1680x1050 pixels (20"). 3. Open 'Advanced Properties' and set the Refresh Rate to 60Hz, then click OK. 4. Restart your computer and repeat step 2 and 3 to verify that your PC is set at 1680x1050@60Hz (20"). 5. Shut down your computer, disconnect your old monitor and reconnect your Philips LCD monitor. 6. Turn on your monitor and then turn on your PC. Q: What does 'refresh rate' mean in connection with an LCD monitor? A: The refresh rate is of much less relevance for LCD monitors. LCD monitors display a stable, flicker-free image at 60Hz. There is no visible difference between 85Hz and 60Hz. Q: What are the .inf and .icm files on the CD-ROM? How do I install the drivers (.inf and . icm)? A: These are the driver files for your monitor. Follow the instructions in your user manual to install the drivers. Your computer may ask you for monitor drivers (.inf and .icm f...