Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
The beam currents of the red, green and blue cannon are accurately measured and compared to the original values stored in the monitor. By readjusting gain values of the individual cannons, deviation is reduced to zero. Default values are stored during production. If the user sets a new color temperature, this new value is saved as the new default value. 15. When should calibration be performed? The calibration process takes less than six seconds. During this period, different specific images are displayed. After the process is finalized, the original image is redisplayed. Constant re-calibration is not required. Calibration should be performed after the monitor is warmed up. Auto Calibration takes place when a monitor receives a signal indicating an imminent switch to its sleep mode/stand-by mode. 16. Which models of Philips monitors are equipped with Auto Calibrate feature? Auto Calibrate is currently available in the new 202P, 201B and 109P. 17. The Main Menu displays OSD MAIN MENU LOCKED . Pressing the front control panels hasno effect. How can I unlock this function? Press and hold the OSD menu key for about 15 seconds until picture displays "OSD MAIN MENU UNLOCKED" 18. My screen shows NO SYNC INPUT , how can I get rid of this? Check the following for possible solutions: l Bent pins on the video cable l Make sure the computer is turned on l Ensure the VGA Cable is properly connected l Ensure the BNC/D-Sub connector on the rear of the monitor is in the correct position, newer models have this option in the On Screen Display under Input Signal Selection. l Video card may be not a VESA standard (try the monitor with another computer) 19. Why does my monitor display "Out of Range"? The video card installed in your computer may be too high for the monitor 's specifications. Please contact your computer manufacturer for details on how to lower resolution for your operating system. 20. What is Moire? Why does my monitor have this wavy phenomenon? Moire is a natural effect or phenomenon of CRT that has the appearance of a wavy pattern, which is repetitive and superimposed on the screen as ripple images. These are a few suggestions to help reduce or minimize the effects: l Some monitors have a Moire cancellation feature, activate it to the on position or adjust the Moire cancellation function via the OSD on the monitor. l Change resolution to the recommended standard for the specific monitor size. l Change Window viewing pattern/scheme to a pattern where the Moire is less visible. l Change horizontal and vertical size to optimize the reduction of the Moire effect. 21. My monitor appears to be missing one or more colors. How do I correct this? l If the OSD menu is also missing a color, please contact service for details l Set color temperature to 9300 color coordination l Check the video cable for any bent pins l Video card could be defective (try the monitor with another computer). 22. When I degauss my monitor, it makes a loud noise. Is this normal? Yes, when degaussing your monitor via the OSD, it is normal for the monitor to make a relatively loud noise. Please be aware that many models will not degauss more than once within any given time period (up to 10 minutes). This is due to the unit having a temperature sensitive resistor. While the unit is degaussing, the resistor increases in value with heat and once it reaches a certain temperature, the resistance will rise and prevent voltage from reaching the degaussing coil. This is what stops the degausser, and this device's resistance will decrease as it cools back off, enabling the degauss function to operate again. This is an intentional design and is an industry standard, not just for Philips monitors. Please be aware that not all models in the Philips range has this manual degauss function. Some models are built with an auto degauss feature which automatically degausses the monitor when it is switched on. 23. How do I adjust the picture on the screen? Please perform the following to correct the picture image: l Reset your monitor via the OSD menu l Adjust the Horz (width) and/or Vert size (height) in the OSD l Change monitor timing to work at the recommended resolution 24. The edge of the picture on the screen appears to be distorted. How can I correct this? Please perform the following to correct the picture image: l A magnetic or electrical interference typically causes poor geometry in the picture. Place the monitor in a different physical location l Reset the monitor to the factory preset via the OSD menu l Access the Geometry Menu in the OSD of the Monitor and perform the necessary adjustments l Change the monitor timing to the recommended resolution 25. The picture appears too dim. How can I correct this? Adjust Brightness and/or Contrast via the monitor 's OSD. Some models have a Video Input Select under Advanced Controls in the monitor 's OSD. Most computers require it to be set at 0.7V. Please review the following for possible solutions: l If the O...
Este manual também é adequado para os modelos :Monitores - 107E76/27 (1.42 mb)
Monitores - 107E71/27B (1.42 mb)
Monitores - 107E71/27 (1.42 mb)
Monitores - 107E71/00 (1.42 mb)