Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
• Remove Control Cover (pinch the Control Cover at the indicated points and pull). • Remove the existing switch (if this is a retrofit application). • Connect the detector as shown in the diagram. Before installing the detector into the box, make sure there is no wire exposed at the connection. • Do not connect to neutral wire or damage to unit will occur. AUTO ON Pinch here 6109 Motion Sensing Wall Switch The 6109 Motion Sensing Wall Switch dectects motion to turn on lights for an adjustable amount of time. A built-in photo cell can be set to keep lights off when the lights aren't needed. The unit has excellent sensitivity and a wide 1800 detection range. It can be used Pinch with incandescent lighting as well as rapid start fluorescent lighting. here Two LEDs allow for easy mode identification. (Not for use with electronic ballasts) Installation is as easy as replacing a wall switch. However, some codes require installation by a qualified electrician. Features include: • 1800 motion detection angle • Adjustable on-time from 12 sec. to 30 min. • Adjustable photocell LOADBLACK • Works with incandescent and rapid start fluorescent lighting (Not TIMEONAUTO TIME LIGHT Green ground wire tojunction box screw orgrounding wire(NEUTRAL) for use with electronic ballasts) • Works with motors up to 1/6 hp. LIGHTINGControl Cover • Push button selectable ON AND AUTO modes. LOAD Plate Removed to access Included are: • The sensor switch • Cover plate • 3 wire connectors • 2 large screws • 2 small screws. INSTALLATION WARNING: For indoor use only. adjustments screws 40' MODE Selection BLACK (LINE) NEW APPLICATION Choose a location where the motion sensor has a clear view of the entire area where occupant motion may occur. Switch HOT SELECT A LOCATION TYPICAL INSTALLATION RETROFIT APPLICATION 20' • Mount the detector into the wall box with the mounting screws. Motion sensing switch will replace existing wall switch. Use only • For test purposes, use a small screwdriver to turn the time control fully counter-clockwise 0' where the existing switch location provides a clear view of the and the light control fully clockwise. Turn the power back on at the circuit breaker. occupied area. Typical Plan View of Coverage • Press MODE selection push button until the AUTO LED is on. Lamp will be on for 12 seconds. Allow two minutes for the unit to warm up. If motion is detected, the lights will turn on. The lights will turn off 12 sec- GENERAL APPLICATION INFORMATION onds after motion is no longer detected. The detector is more sensitive to motion across the front of the sensor than to motion towards the sensor. The detector senses heat in motion and possible heat sources that change temperature quickly. Therefore, to Questions? Call 1-866-853-4293 8:00 AM to 7:00 PM Eastern Time, weekdays avoid false triggering, avoid placing the sensor where it will be aimed at air conditioners, heaters, and other sources of heat or cold. 469MX-PT - 2 TIME The length of time that the lights stay on is adjustable from 12 seconds to 30 minutes. • Use a small screw driver to set the time by using the diagram below as a guide. ADJUSTMENTS TROUBLESHOOTING LIGHT LEVEL If you have a problem with your Wall Switch, first follow this guide. If the problem persists, call the customer The sensor can be prevented from turning on lights when service hotline at 1-866-853-4293 between 8:00 AM and 7:00 PM ET weekdays. there is already enough light in the room. Use a small screw driver to set the light level using this diagram as a guide. In the fully clockwise position, the sensor turns on lights even in full daylight. In the fully counter-clockwise poition, the sensor only turns on lights when the surrounding light level is very low. To adjust the photocell: SYMPTOM POSSIBLE CAUSE Light does not Circuit breaker or fuse is turned1. come on. off. If the lamp being controlled has2. another switch, it may be turned off. Bulb is defective. LIGHT control is set too far 3. 4. toward the DARK position. MODE switch is set to OFF5. instead of AUTO. Incorrect wiring.6. Lights do not Motion has stopped in the room.1. stay on in the TIME control is set for too short a Auto mode. delay.2. SYMPTOM POSSIBLE CAUSE Light does Incorrect wiring.1. not turn off. MODE switch is set to ON instead of AUTO. Motion is still present. Delay set by TIME control has not expired. 2. 3. 4. Light comes Heating or cooling ob1. on for no jects (such as air vents, reason in appliances, or drafts through the the wall box) are causing Auto mode. false triggering. Switch on the sensor has been turned off and back on.2. There was a momentary power interrup-tion. The light will turn off automatically3. when the "on" time expires. Dark (low Any Light 12 Sec. AUTO LED light level) • When the light in the room is at Level TIMELIGHT++ the level you want the lights to turn on, set the switch to the 30 Min. AUTO position. • Put the TIME control to the 12 sec. (fully counter-clockwise) position. • Put the LIGHT c...