Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
Release the display panel from the display stand as follows: • Remove the neck cover (1) by sliding it upward. • Lift the plastic frame (2) that covers the fixation of the panel to the stand. Turn it for 45 degrees to uncover the fixation screws. • Unscrew the four fixation screws fixing the panel to the stand. 1 2 Vesa-mount installation 2. Attach the panel firmly to the arm stand using 4 screws M4 x 10 mm. 3. You should mount the panel in landscape position. Portrait position is not supported. Cleaning instructions Cleaning instructions Precautions Precautions • Before cleaning, switch the display in stand-by position to prevent the control touch keys from being activated inadvertently by sweeping over the front filter. In stand-by position the touch keys cannot be activated by just sweeping over them. To switch the display on again, you must press the stand-by touch key for a few seconds. • Take care not to damage or scratch the front filter or LCD panel. Be careful with rings or other jewelry that can touch the front filter. • Do not apply pressure on the front filter or LCD panel. • Do not apply or spray liquid directly to the front filter, panel or cabinet as excess liquid may cause damage to internal electronics. Instead, apply the liquid to the cleaning cloth. Front glass Proceed as follows: Clean the glass using a sponge, cleaning cloth or soft tissue, lightly moistened with one of the following tested products: •Flux •Windex Glass Plus • Bohle glass cleaner • Mr. Proper •Pril •Ajax glass cleaner Cleaning instructions • Sidolin glass cleaner In case none of the above cleaning products is available, use plain water. Do NOT use: • Alcohol/solvents at higher concentration > 5% • Strong alkalis lye, strong solvents •Acid • Detergents with fluoride • Detergents with ammonia • Detergents with abrasives • Steel wool • Sponge with abrasives • Steel blades • Cloth with steel thread Cabinet Proceed as follows: • Clean the cabinet using a soft cotton cloth, lightly moistened with a recognized cleaning product for medical equipment. • Repeat with water only. • Wipe dry with a dry cloth. • The cabinet has been tested for resistance to the following products: • Cidex, Betadine • Alcohol (Isopropyl and Ethyl) • Ammonia-based cleaners (Windex) •Aquasonic Gel Software installation Software installation Driver and Software Installation Driver and Software Installation This chapter will guide you through the installation of the drivers, software and documentation associated with your Barco Coronis Fusion 6MP Display System or Barco Coronis Fusion 6MP Display(s). Driver and software installation prerequisites Note: To install or remove the drivers, software, or documentation you must be logged on as a user with administrator privileges. Your operating system must be installed and running before you can install the driver, software and documentation for the Barco display controller(s) for your BARCO CORONIS FUSION 6MP Display System. Before you begin make sure that all of your Barco Coronis Fusion 6MP Display(s) is connected to the appropriate display controller(s) in your system. Note: This installation procedure is based on operating Windows in “Classic” theme. If “Aero” or “Basic” theme is selected in Windows, sections of this procedure may be different than what is listed. Installing the BARCO MXRT drivers and software Note: The installation dialog will display in English if your operating system’s language is not supported. This process applies to the following versions of Windows: • Windows 7 32 & 64 Bit You will need to install the Barco Coronis Fusion 6MP Display system drivers and software in the following cases: Driver and Software Installation • After you have installed the Barco display controller(s) for your BARCO CORONIS FUSION 6MP Display System in your system for the first time. • After you have reinstalled or upgraded your operating system. • When you upgrade to a newer version of the MXRT driver. Note: You do not need to manually uninstall an existing driver before updating to the current version. The Barco Product Installation Wizard will detect any prior installations and start the uninstallation process automatically if necessary. Note: When there is a non-Barco board in the system, we recommend that you first install the driver for the non-Barco board, prior to installation of the Barco driver. After each driver installation, you should reboot the system, before proceeding with installation of another driver. 1. Start your system. If you have a fresh OS installation, the OS will automatically install an ATI driver (Windows 7 inbox driver) for the Barco MXRT Graphics Card(s). When the OS prompts you to restart your computer, click yes, to allow the automatic driver installation to complete, and reboot the system. 2. Launch the Barco Product Installation Wizard. The installation Wizard should start automatically when you insert the Barco Display System Installation DVD into your computer's DVD drive...
Este manual também é adequado para os modelos :Monitores - Coronis Fusion MDCC 6130 (929.18 kb)