Assessments - 1, GPA: 3 ( )

Fabricante : AMX Arquivo Tamanho: 3.29 mb Arquivo Nome : Modero.1200V.OperationReferenceGuide.pdf Língua de Ensino:

Set the page flip Syntax: password. "'@PWD-'" Variables: page flip password = 1 - 50 ASCII characters. Example: SEND COMMAND Panel,"'@PWD-Main'" Sets the page flip password to 'Main'. ^PWD Password level is required and must be 1 - 4. Set the page flip Syntax: password. "'^PWD-,'" Variables: password level = 1 - 4. page flip password = 1 - 50 ASCII characters. Example: SEND COMMAND Panel,"'^PWD-1,Main'" Sets the page flip password on Password Level 1 to 'Main'. @RPP @RPP resets the protected password to its default (1988). Reset the Syntax: protected "'@RPP'" password. Example: SEND COMMAND Panel,"'@RPP'" Resets the protected Setup page password to ‘1988’. ^VOL Syntax: Set the panel "'^VOL-'" volume. Variable: volume level = 0 - 100. 100 is maximum volume setting. Example: SEND_COMMAND Panel,"'^VOL-50'" Set the panel volume to 50. NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Programming Dynamic Image Commands The following table describes Dynamic Image Commands. Dynamic Image Commands ^BBR Syntax: Set the bitmap of "'^BBR-,,'" a button to use a Variable: particular variable text address range = 1 - 4000. resource. button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons 1 = Off state and 2 = On state). resource name = 1 - 50 ASCII characters. Example: SEND_COMMAND Panel,"'^BBR-700,1,Sports_Image'" Sets the resource name of the button to ’Sports_Image’. ^RAF Adds any and all resource parameters by sending embedded codes and data. Add new Since the embedded codes are preceded by a '%' character, any '%' character contained resources. in the URL must be escaped with a second '%' character (see example). The file name field (indicated by a %F embedded code) may contain special escape sequences as shown in the ^RAF, ^RMF - Embedded Codes table below. Syntax: "'^RAF-,'" Variables: • resource name = 1 - 50 ASCII characters. • data = Refers to the embedded codes, see the ^RAF, ^RMF - Embedded Codes section on page 153. Example: SEND_COMMAND Panel,"'^RAF-New Image,%P0%HAMX.COM%ALab/ Test%%5Ffile%Ftest.jpg'" Adds a new resource. • The resource name is ’New Image’ • %P (protocol) is an HTTP • %H (host name) is AMX.COM • %A (file path) is Lab/Test_file • %F (file name) is test.jpg. Note that the %%5F in the file path is actually encoded as %5F. ^RFR Syntax: Force a refresh for "'^RFR-'" a given resource. Variable: resource name = 1 - 50 ASCII characters. Example: SEND_COMMAND Panel,"'^RFR-Sports_Image'" Forces a refresh on ’Sports_Image’. NXD/T-1200V 12" Modero® Video Wall/Flush Mount Touch Panel Programming Dynamic Image Commands (Cont.) ^RMF Modifies any and all resource parameters by sending embedded codes and data. Modify an Since the embedded codes are preceded by a '%' character, any '%' character contained existing resource. in the URL must be escaped with a second '%' character (see example). The file name field (indicated by a %F embedded code) may contain special escape sequences as shown in the ^RAF, ^RMF - Embedded Codes section on page 153. Syntax: "'^RMF-,'" Variables: • resource name = 1 - 50 ASCII characters • data = Refers to the embedded codes, see the ^RAF, ^RMF - Embedded Codes section on page 153. Example: SEND_COMMAND Panel,"'^RMF-Sports_Image,%ALab%%5FTest/ Images%Ftest.jpg'" Changes the resource ’Sports_Image’ file name to ’test.jpg’ and the path to ’Lab_Test/ Images’. Note that the %%5F in the file path is actually encoded as %5F. ^RSR Syntax: Change the "'^RSR-,'" refresh rate for a Variable: given resource. resource name = 1 - 50 ASCII characters. refresh rate = Measured in seconds. Example: SEND_COMMAND Panel,"'^RSR-Sports_Image,5'" Sets the refresh rate to 5 seconds for the given resource (’Sports_Image’). ^RAF, ^RMF - Embedded Codes The ^RAF and ^RMF commands add and modify any and all resource parameters by sending embedded codes and data: "'^RAF-,'" "'^RMF-,'" The variable uses the embedded codes described in the following table: ^RAF, ^RMF - Embedded Codes Parameter Embedded Code Description protocol ’%P <0-1>’ Set protocol. HTTP (0) or FTP (1). user ’%U ’ Set Username for authentication. password ’%S ’ Set Password for authentication. host ’%H ’ Set Host Name (fully qualified DNS or IP Address). file ’%F ’ Full path to the location of the file or program that will return the resource. The path must be a valid HTTP URL minus the protocol and host. The only exception to this is the inclusion of special escape sequences and in the case of FTP protocol, regular expressions. path ’%A ’ Set Directory path. The path must be a valid HTTP URL minus the protocol, host and filename. The only exception to this is the inclusion of special escape sequences and in the ...

Baixe o seu

Para fazer o download, introduza 2 dígitos :