Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
Multimedia Features The M150 FPD monitor comes with multimedia features built-in. It has a microphone and speakers built into the back of the display bezel and includes multimedia cables. These cables can be connected from either the rear of the monitor or in front -- two separate sets of jacks are included. Figure 5 Multimedia Cables Optional Card Reader Bracket The M150 FPD monitor is available with an optional card reader bracket (and (2) M3 screws) that supports IDTech and MagTech brand electronic card readers. The M150 has been designed with slots on either side of the bezel to accommodate this card reader bracket. Simply slide the bracket into the appropriate holes and pull down slightly to lock in place. Refer to the illustration below for wiring suggestions. Note that 3M Touch Systems does not supply these card readers. Supported MagStripe Readers At the time of publication, the following “mini” magnetic card readers have been tested to fit the 3M Touch Systems optional card reader bracket. Consult your card reader sales representative for model numbers not listed here. ID Tech MagTek all MiniMag™ readers all "mini" sized readers IDT 3331-02U IDT 3321-33 2180201 IDT 3331-12U IDT 3321-33PP 2180202 IDT 3331-23U IDT 3331-02 2180203 IDT 3331-33U IDT 3331-12 2180204 IDT 3321-02 IDT 3331-23 2180205 IDT 3321-02PP IDT 3331-33 2180206 IDT 3321-12 IDT3301-02 21040103 IDT 3321-12PP IDT3301-12 21040104 IDT 3321-23 IDT3301-23 IDT 3321-23PP IDT3301-33 Figure 6 Card Reader Mounting and Cable Management 65-2305 Connecting the Touch Monitor CAUTION You are cautioned that any change or modification to the equipment not expressly approved by the party responsible for compliance could void your authority to operate such equipment. To connect the M150 FPD monitor: 1. Turn off your computer. You should always turn off the computer before connecting or disconnecting any device. 2. Connect one end of the video cable to the video connector on the FPD. Connect the other end to the video card in your computer. 3. Connect one end of the touch screen cable (either serial or USB) to the FPD. Connect the other end to an available port on the back of your computer. If you are using a USB connection, make sure you have installed the TouchWare drivers prior to connecting the touch screen cable. 4. Plug the AC/DC power supply into the M150 FPD. Be sure to use the power supply included with the monitor. Figure 7 Identifying Your Monitor Connections WARNING To avoid the risk of electric shock which could result in serious injury or death: This device must be operated with the original power supply, part number: HJC, HASU05F or CHI, CH-1234. CAUTION To avoid the risk of electric shock which may result in minor or moderate injury: The socket-outlet should be installed near the equipment and should be easily accessible. Use a power cable that is properly grounded. Always use the appropriate AC cord certified for the individual country. Some examples are listed below: USA UL Switzerland SEV Canada CSA Britain BASE/BS Germany VDE Japan Electric Appliance Control Act 5. Connect the power cable to the AC/DC supply. Connect the other end to the appropriate AC outlet. Figure 8 Connecting the M150 Cables to your Computer You should be sure all cable connections are secure -- tighten all cable screws. Shaking and vibration may dislodge cables that are improperly connected. Line Callout 2 (No Border): Line In Line Callout 2 (No Border): Touch Screen Line Callout 2 (No Border): Microphone out Line Callout 2 (No Border): Power Line Callout 2 (No Border): Video Connection Route all wiring and cabling away from heat sources and sharp metal edges to avoid damage. Also, keep the touch screen cable away from sources of electromagnetic and radio frequency interference. WARNING To avoid the risk of electric shock which could result in serious injury or death: • Do not use a damaged power supply. • Do not use a power cord that is frayed or otherwise damaged. Cable Management System Figure 9 Removing the Cable Management Cover 65-2303 Once you have connected your M150 FPD monitor to your computer, you should take advantage of the cable management system designed into the base of the M150 FPD monitor as shown above. In order to properly route all cables through the cable management system, the cover on the base unit must be removed. To remove this cover: 1. Push in and lift up on each of the two tabs located on the left and right sides of the cover. This action will release the cover tabs from the base. 2. Slide the cover back towards you to remove. Testing the M150 FPD Note: The M150 FPD has a power status light located on the front of the bezel. After connection, turn on the power switch located at the bottom of the front bezel. Before you test your touch monitor, make sure all cables are connected properly and routed through the cable management system. Be sure to tighten all cable screws. To test that the monitor is working properly: 1. Turn on your compu...