This stand is q specifically designed only for the Daewoo Plasma Display. To ensure the safe operation of the unit, please read these instructions before installing. TABLE OF CONTENTS 1. Check for enclosed parts............................1 2. Important Safety Instructions......................2 3. Assembly Instructions.................................3 4. Disassembling Instructions.........................5 1. PLEASE CHECK FOR THE ITEMS SHOWN BELOW 1 PLASMA DISPLAY STAND 2. IMPORTANT S

e the unit to fall and break) A When installing, be sure to have at least two people handling the unit. A When attaching stand to plasma display, be sure to cover the surface to protect from (It may result in unwanted marks on the units, if working without the protective covering) S T A N D 2 3. ASSEMBLING INSTRUCTIONS 1 1 HOW TO DISPOSE OF THE PLASMA MONITOR WRAPPER ■ First dispose of the wrapping band and raise the top box to open. Afterwards, dispose of the Styrofoam and remov

CAUTION : Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CANADIAN NOTICE This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. AVIS CANADIEN Cet appareil numerique de la Class B respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada. WICHTIGE INFORMATIONEN Bitte lesen Sie alle diese Informationen, nehmen! Lesen

For Daewoo technical support call 1-800-245-9870.) Model : 531X DAEWOO ELECTRONICS CO., LTD. http : //svc.dwe.co.kr September, 2000 CONTENTS SAFETY PRECAUTIONS GENERAL SAFETY INFORMATION SERVICING PRECAUTIONS TECHNICAL INFORMATION GENERAL INFORMATION PIN CONNECTOR CAUTIONS FOR ADJUSTMENT AND REPAIR OPERATION AND ADJUSTMENT 9 ALIGNMENT PROCEDURE 12 TROUBLESHOOTING HINTS 15 BLOCK DIAGRAM 29 PCB LAYOUT 30 SCHEMATIC DIAGRAM 33 EXPLODED VIEW DIAGRAM 37 INFORMATION OF PART DESCRIPTION 38 ELECTRICAL PA

These speakers are specifically designed only for the Daewoo Plasma Display. To ensure the safe operation of the unit, please read these instructions before installing. TABLE OF CONTENTS 1. Check for enclosed parts ............................ 2 2. Important Safety Instructions ...................... 3 3. Assembly Instructions ................................. 5 1) Using speakers when attached to the plasma display 2) Using speakers on its own stand 1 PLASMA DISPLAY SPEAKER 1. PLEASE CHECK THE F

To ensure the safe operation of the unit, please read these instructions before installing. TABLE OF CONTENTS 1. Check for enclosed parts ............................ 2 2. Important Safety Instructions ...................... 3 3. Assembly Instructions ................................. 5 1) Using speakers when attached to the plasma display 2) Using speakers on its own stand 1 PLASMA DISPLAY SPEAKER 1. PLEASE CHECK THE FOLLOWING ITEMS SHOWN BELOW SPEAKER (2) (2) VIBRATION ABSORBENT SPONGE (16) M5

(Doing so may cause the speakers to fall off or tip over causing injury and damage.) 3 PLASMA DISPLAY SPEAKER 4 SPE AKE R Please be careful not to stain the speakers with any gas or oil. When assembling, be sure to use the enclosed parts and make sure all parts are tightly screwed as instructed. Do not place the speakers in a humid or dusty place. Do not place the speakers near heating units. Do not place speakers near a humidifier, or cooking pots where speakers will be exposed to steam or smok

Abnormal Picture 9-1. Horizontal Size When the VR601 is changed, is the H.size changed? No Yes Check pin 15 of IC501 and its ambient circuit (D604, R605, R606, R607) It isn't out of order. Is the H.Size about 295mm at VGA mode and Min. H.Size in OSD Menu? No Yes 1.Check B+ section of TDA9109 and its ambient circuit. 2.Check Q601 and its ambient circuit. Abnormal H.Size 25 9-2. Vertical Size Is changeable the DC voltage of IC401 pin 1? Check the IC401 and its ambient circuit Check the IC501 and i

U.S.FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INFORMATION TO THE USER NOTE : This equipment has Class B digital device pursuant These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particula

Under the law, copying includes translation into another language. Copyright © 1996, Delta-T Devices Limited. SunData software and canopy theory are Copyright © 1996 John Wood, Peak Design, Wensley Road, Winster, Derbyshire, U.K. Acknowledgements Extracts and illustrations from the Psion Workabout documentation are Copyright © 1995 Psion PLC, and are reprinted here by kind permission of Psion PLC. Trademarks Psion and the Psion logo are registered trademarks, and Psion Workabout, 3Link, SSD and