Log:
Assessments - 1, GPA: 3 ( )

Instruções de Operação Aiwa, Modelo CSD-EL300

Fabricante : Aiwa
Arquivo Tamanho: 1.43 mb
Arquivo Nome : b4aa2c6a-8b83-4fe7-894e-773627a01dda.pdf
Língua de Ensino: enesfr
Ir para baixar



Facilidade de uso


Owner’s record For your convenience, record the model number and serial number (you will find them on the rear of your set) in the space provided below. Please refer to them when you contact your Aiwa dealer in case of difficulty. Model No. Serial No. (Lot No.) CSD-EL300 2 ENGLISH TABLE OF CONTENTS PREPARATIONS POWER SUPPLY ................................................................. 4 REMOTE CONTROL ........................................................... 4 BEFORE OPERATION ........................................................ 5 SETTING THE CLOCK ........................................................ 5 SOUND ADJUSTING THE SOUND ................................................... 6 TAPE PLAYBACK TAPE OPERATIONS............................................................ 7 RADIO RECEPTION MANUAL TUNING ............................................................... 8 PRESETTING STATIONS .................................................... 9 CD PLAYING CD OPERATIONS .............................................................. 10 RECORDING RECORDING ..................................................................... 12 TIMER TIMER PLAY/TIMER RECORDING ................................... 13 SETTING THE SLEEP TIMER ........................................... 13 GENERAL CARE AND MAINTENANCE ............................................. 14 TROUBLESHOOTING GUIDE .......................................... 14 SPECIFICATIONS ............................................................. 15 PARTS INDEX.....................................................Back cover En ENGLISH 3 PREPARATIONS PREPARATIONS POWER SUPPLY USING ON AC HOUSE CURRENT Connect the AC cord as illustrated below. 1 to the AC inlet of the unit 2 to an AC outlet AC cord (supplied) (AC 120 V, 60 Hz) The OPE/BATT indicator lights up while the power is on. CAUTION Use only the supplied AC cord. Use with other cords may result in the risk of fire. USING ON BATTERIES Open the lid of the battery compartment on the rear and insert eight R14 (size C) batteries, not supplied, as illustrated below. Then close the lid. To switch from AC power supply to battery power supply, disconnect the AC cord from the AC inlet. • When using the unit on the batteries, the display will not be illuminated. The batteries need to be replaced when: The OPE/BATT indicator becomes dim, the tape speed slows down, volume decreases, or sound is distorted during operation. Notes on batteries To avoid damage from leakage or explosion, observe the following: • Insert the batteries with the 0and 9marks correctly aligned. • Do not mix different types of batteries or old batteries with new ones. • Never recharge the batteries, apply heat to them or take them apart. • Remove dead batteries. If liquid leaks from the batteries, wipe thoroughly to remove. NOTE If power is interrupted for more than 12 hours, all settings stored in memory, such as the clock, the timer, and the presetting of the broadcasting stations, are cleared and need to be set again. REMOTE CONTROL INSERTING BATTERIES Detach the battery cover on the rear of the remote control and insert two R03 (size AAA) batteries. When to replace the batteries The maximum operational distance between the remote control and the remote sensor on the main unit should be approximately 5 meters (16 feet). When this distance decreases, replace the batteries with new ones. USING THE REMOTE CONTROL Some operations can be performed using the buttons on the remote control only, or those on the main unit only, while others can be performed using the buttons on the main unit as well as the remote control. This instructions manual clearly describes the buttons available for each operation. To use the buttons Point the remote control at the REMOTE SENSOR on the main unit to use the buttons on the remote control. NOTE • If the unit is not going to be used for an extended period of time, remove the batteries to prevent possible electrolyte leakage. • The remote control may not operate correctly when: – The line of sight between the remote control and the unit is exposed to intense light, such as direct sunlight – Other remote controls are used nearby (television, etc.) • The cbutton on the remote control has the same function as that of the dbutton on the main unit. 4 ENGLISH BEFORE OPERATION SETTING THE CLOCK To turn the unit on Press one of the function buttons (TAPE/REV MODE, TUNER/BAND, CD). Playback of the inserted disc or tape begins, or the previously tuned station is received (Direct Play Function). The POWER button is also available. Pressing the zCD OPEN button turns the unit on as well. After use Press the POWER button to turn off the power. The display changes to the clock. NOTE When using on the batteries, you cannot turn the power on with the remote control. To use the headphones Connect headphones with a stereo mini plug (o3.5 mm, 1/8 inch) to the PHONES jack. No sound is output from the speakers while the headphones are plugge...


Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias